Important• Do not move the carriage over jammed paper. This may damage the print head.2. Remove any jammed paper inside top cover.2.After removing the paper, make sure there are no other scraps of paper in the printer.3. Close top cover.3.Important• Do not touch the linear scale (A) or carriage shaft (B). This may stain your hands and•damage the printer.613

Canon imagePROGRAF GP-5300 Online Manual

GP200

installation instructions

PROCEDURE

B. POINTS TO NOTE FOR SCHEDULED SERVICING

A. MECHANICAL

routing the scanner drive cable

B. ELECTRICAL SYSTEM

A. INITIAL CHECKS

E000 (Fixing temperature fails to rise.)

E001 (Fixing temperature is abnormally high.)

E007 (The fixing film has become displaced.)

E007-01 (The fixing film fails to return.)

E010 (The main motor fails to lock.)

E032 (The copy data controller counter is faulty.)

E064 (The high-voltage output is faulty.)

E100 (BD error)

E110 (The laser scanner motor fails to lock.)

between DC controller PCB and composite power supply PCB

E202 (Scanner home position is not detected; no code indication is made.)

reverse

The pre-exposure lamp fails to turn ON

The fixing heater fails to operate

The Jam message fails to turn OFF

The fax error indicator fails to turn OFF

A. COPY PAPER JAMS

B. FEEDING FAULTS

A. CLUTCHES AND SOLENOIDS

B. MOTORS

D. SENSORS

E. SWITCHES AND COUNTERS

G. FAX-RELATED PCBS

EMITTING DIODES (LED), AND CHECK PINS BY PCB

image processor pcb

A. OUTLINE

B. USING SERVICE MODE

C. USING ADJUSTMENT MODE AND SETTINGS MODE

F. *3* ADJUST (ADJUSTMENT MODE)

G. *4* FUNCTION (FUNCTION MODE)

H. *5* OPTIN (SETTINGS MODE)

I. *6* COUNTER (COUNTER MODE)

J. *7* ACC (ACCESSORY MODE)

A. COPIER

B. SELF DIAGNOSIS OF THE RDF-G1

D. SELF DIAGNOSIS OF THE PEDESTAL

F. SELF DIAGNOSIS OF THE MULTI OUTPUT TRAY-12

A. GENERAL TIMING CHART

B. SIGNALS AND ABBREVIATIONS

C. GENERAL CIRCUIT DIAGRAM

I. FEATURES

II. SPECIFICATIONS

III. NAMES OF PARTS

B. Cross Section

C. Arrangement of Extension Boards

IV. OPERATION

B. Control Panel

C. Basic Operation

D. Extension Mode

timer setting

V. ROUTINE WORK BY THE USER

VI. SAFETY

B. Safety of Toner

I. IMAGE FORMATION

B. Latent Image Formation Block

C. Pre-Exposure (step 1)

E. Laser Exposure (step 3)

G. Transfer (step 5)

H. Separation (step 6)

I. Fixing (step 7)

II. AUXILIARY PROCESS

I. BASIC OPERATION

B. Outline of the Electrical Circuitry

general block diagram

C. Inputs to the Major PCBs

D. Main Motor Control PCB

II. ORIGINAL EXPOSURE SYSTEM

B. Varying the Reproduction Ratio

D. Scanner Motor

E. Controlling the Scanning Lamp

F. Identifying the Size of Originals

detecting the size of originals

III. IMAGE PROCESSING

B. Analog Image Processing

C. Digital Image Processing

shading correction

IV. LASER EXPOSURE SYSTEM

B. Generating the BD Signal

C. Laser Driver Circuit

D. Controlling the Laser Scanner Motor

V. IMAGE FORMATION SYSTEM

B. Controlling the Primary Charging Roller Bias

vi. pick-up/feeding system

basic sequence of operations

c. non-pick up operation (standby)

e. detecting the size of copy paper

h. making overlay copies

k. fixing/delivery assembly

sequence of operations

M. Detecting Jams

jam history

VII. FANS

VIII. POWER SUPPLY

B. SLEEP Mode

IX. SYSTEM

B. Diagram of the Function Boards

C. Flow of Image Signals

X. SERVICE MODE

B. Using Service Mode

C. Using Adjustment Mode and Settings Mode

E. *2* I/O DISPLAY(I/O display mode)

F. *3* ADJUST (adjustment mode)

G. *4* FUNCTION (function mode)

I. *6* COUNTER (counter mode)

J. *7* ACC (accessory mode)

K. Electrical System

XI. SELF DIAGNOSIS

B. Self Diagnosis of the RDF-G1

D. Self Diagnosis of the Pedestal

F. Self Diagnosis of the Multi Output Tray-12

I. BEFORE THE WORK POINTS TO NOTE

B. Handling the Harnesses

II. EXTERNALS

B. Inside Cover

C. Control Panel

III. DRIVE ASSEMBLY

routing the scanner cable

B. Fixing Drive Assembly

C. Duplexing Unit Inlet Motor Mount Assembly

E. Pick-Up Drive Assembly

IV. PICK-UP ASSEMBLY

B. Multifeeder Assembly

C. Feeding Assembly

D. Lower Feeding Assembly

F. Delivery Assembly

V. EXPOSURE

c. ipu pcb

D. Laser Scanner Assembly

VI. DEVELOPING SYSTEM

VII. FIXING SYSTEM

VIII. ELECTRICAL SYSTEM

c. replacing the rom dimm

I. SELECTING THE SITE

II. UNPACKING AND INSTALLATION

A. Unpacking

service manual

copying process

Multi Output Tray-12

B. Supplying Toner

C. Stirring the Toner

D. Installing the Drum Cartridge

E. Installing the Cassettes

F. Installing the Feeder

G. Machine Specifications Setting Mode (*5*)

H. Fax Settings (for machines equipped with fax functions)

I. Checking the Copy Images

shading adjustment

automatic density adjustment

GP-5200

GP-5300

imagePROGRAF GP-300