Canon imageRUNNER 2545 Series Service Manual Digest

Also see for imageRUNNER 2535: Printer guide User guide Client guide User guide Easy operation guide

Contents

3-93FAX Error CodeOutlineError Code OutlineAn error code is used to indicate a fault in a machine, and is indicated in the machine's LCDor reports, showing the nature (symptoms) of the fault. Using the errorcode, the user or theservice man can readily find out how to correct the fault by simply referring to the User'sManual or service manual. An error code may be either of the following two types:User Error CodesA fault indicated as a user error code is one that can easily be corrected by the user, as byoperating the machine. It takes the form of "# + number."Service Error CodesIf a fault calls for a service man for correction, it is indicated as a service man error code inthe form of "## + number" or "SYSTEM ERROR E + number."MEMO:- A service error code expressed in the form of "## + number" will not appear on theLCD, Error Tx Report, or Activity Report while the machine remainsin factory defaultstate. To check a service error code, shift bit 0 of service soft switch #1 SSSW SW01to '1'.- For the causes and countermeasures of error codes, refer to the separate G3/G4Facsimile Error Code List.User Error CodeUser Error CodeNo. Tx/Rx Description#0001 [Tx] An original has jammed.#0003 [Tx/Rx] Time-out for copying or sending/receiving a single page has occurred.#0005 [Tx/Rx] Time-out for initial identification (T0/T1) has occurred.#0009 [Rx] Recording paper has jammed or is absent.#0012 [Tx] Recording paper is absent at the other party.#0018 [Tx/Rx] Auto call initiation has failed.#0037 [Rx] Image memory overflow at time of reception has occurred.#0059 [Tx] The number you dial and connected number (CSI) does not match.#0995/0099 [Tx/Rx] A memory communication reservation has been cancelled.••T-3-3T-3-3Service Error CodeService Error CodeNo. Tx/Rx Description##0100 [Tx] At time of transmission, the procedural signal has been transmitted more thanspecified.##0101 [Tx/Rx] The modem speed does not match that of the other party.##0102 [Tx] At time of transmission, fall-back cannot be used.##0103 [Rx] At time of reception, EOL cannot be detected for 5 sec (15 sec if CBT).##0104 [Tx] At time of transmission, RTN or PIN is received.##0106 [Rx] At time of reception, the procedural signal is received for 6 sec while in wait forthe signal.##0107 [Rx] At time of reception, the transmitting party cannot use fall-back.##0109 [Tx] At time of transmission, a signal other than DIS, DTC, FTT, CFR, or CRP isreceived, and the procedural signal has been sent more than specified.##0111 [Tx/Rx] Memory error has occurred.##0114 [Rx] At time of reception, RTN is transmitted.##0200 [Rx] At time of reception, no image carrier is detected for 5 sec.##0201 [Tx/Rx] DCN is received outside the normal parity procedure.##0224 [Tx] Communication protocol signal error.##0228 [Rx] Abnormal management information of image data.##0232 [Tx] Encoding error has occurred.##0237 [Rx] Decoding error has occurred.##0261 [Tx/Rx] System error has occurred.##0280 [Tx] At time of transmission, the procedural signal has been transmitted more thanspecified.##0281 [Tx] At time of transmission, the procedural signal has been transmitted more thanspecified.##0282 [Tx] At time of transmission, the procedural signal has been transmitted more thanspecified.##0283 [Tx] At time of transmission, the procedural signal has been transmitted more thanspecified.##0284 [Tx] At time of transmission, DCN is received after transmission of TCF.##0285 [Tx] At time of transmission, DCN is received after transmission of EOP.##0286 [Tx] At time of transmission, DCN is received after transmission of EOM.##0287 [Tx] At time of transmission, DCN is received after transmission of MPS.##0288 [Tx] After transmission of EOP, a signal other than PIN, PIP, MCF, RTP, or RTNhas been received.##0289 [Tx] After transmission of EOM, a signal other than PIN, PIP, MCF, RTP, or RTNhas been received.##0290 [Tx] After transmission of MPS, a signal other than PIN, PIP, MCF, RTP, or RTNhas been received.##0670 [Tx] At time of V.8 lAte start, the V.8 ability of DIS front the receiving party isexpected to be detected, and the CI signal is expected to be transmitted inresponse; however, the procedure fails to advance, and the line is releasedbecause of T1 time-out.