AUTOMATIC OPERATION (AUTOCHANGEOVER)FILTER PRE DEF TIMER OPERATIONRESETModels: 42NQ012, 42NQV012SModels: 42NQ009, 42NQV009S1 Press FIX : Move the louver inthe desired vertical direction.2Press SWING: Swing the airautomatically and press againto stop.3 For horizontal direction, adjustmanually.DANGER• Do not install, repair, open or remove the cover. It may expose you todangerous voltages. Ask the dealer or the specialist to do this.• Turning off the power supply will not prevent potential electric shock.• The appliance shall be installed in accordance with national wiringregulation.• Means for disconnection from the supply having a contact separationof at least 3 mm in all poles must be incorporated in the fixed wiring.WARNING• Do not expose your body directly to cool air for a long time.• Do not insert your finger or any article into the air inlet/outlet.• When an abnormality (burning smell, etc.) occurs, stop the airconditioner and disconnect the power supply or turn off the breaker.CAUTION• Do not wash the unit with water. It may cause an electric shock.• Do not use this air conditioner for other purposes such as preservingfood, breeding animal, etc.• Do not step or put anything on the indoor/outdoor unit. It may causean injury or damage the unit.• Do not touch aluminium fin because it may cause an injury.• Before cleaning the unit, turn off the main switch or the circuitbreaker.• When the unit won’t be used for a long time, turn off the main switchor the circuit breaker.• It is recommended that maintenance be performed by a specialistwhen the unit has been operated for a long time.PRECAUTIONS FOR SAFETYINDOOR UNIT DISPLAY1 FILTER (Orange)2 PRE DEF (DE-FROST) (Orange)3 TIMER (Yellow)4 OPERATION (Green)5 RESET button1PREPARATION BEFORE USE2Preparing Filters1. Open the air inlet grille and remove the air filters.2. Attach the filters. (see detail in the accessory sheet)Loading Batteries1. Remove the cover. Insert 2 newbatteries (AAA type) following the(+) and (–) positions.2. Push RST : Reset the remotecontrol.3. Place the cover back.AIRFLOW DIRECTION3Note:• Do not move the louver manually by others.• The louver may move automatically positioning by operation mode.A C L1 OPERATION (Green)2 TIMER (Yellow)3 RESET buttonREMOTE CONTROL FUNCTION41 Infrared signal emitter2 Set louver button (FIX)3 Auto louver button (SWING)4 Mode select button (MODE)5 Reset button (RST)6 On timer button (ON)7 Off timer button (OFF)8 Reserve button (SET)9 Cancel button (CLR)! Check button (CHK)" ECO button (ECO)# Fan speed button (FAN)$ Start/Stop button (START/STOP)% Temperature button ( )5To automatically select cooling or fan only operation and control fan speed.1. Press MODE : Select AUTO.2. Press : Set the desired temperature.The manufacture setting temperature is 24°C and available range of settemperature is ±5°C.COOLING / HEAT / AUTO FAN OPERATION61. Press MODE: Select COOL, HEAT or AUTO FAN.2. Press : Set the desired temperature.COOL: Min 17o C, HEAT: Max 30o C, AUTO FAN :No temperature indication3. Press FAN : Select AUTO, LOW , MED , HIGH .DRY OPERATION7For dehumidification, a moderate cooling performance is controlledautomatically.1. Press MODE : Select Dry.2. Press : Set the desired temperature.ECONOMICAL OPERATION8To automatically control room temperature, fan speed and operation mode1. Press ECO in the AUTO and COOL operation: Start and stop theoperation.2. Press MODE or FAN after stopping the operation.Note:• Under certain conditions, ECO mode may not provide adequate coolingdue to energy saving features.TEMPORARY OPERATION9SWINGMODETIMERON OFF SET CLRECORST CHKFIX FANHr.ON OFF5439"#$%87612!CLEANINGRESET TIMER OPERATIONIn case of the misplaced or discharged remote control• Pressing the RESET button, the unit can start orstop without using the remote control.• Operation mode is set onAUTOMATIC operation, presettemperature is 24°C and fanoperation is automatic speed.