Carrier 19XR User Manual

Also see for AquaEdge 19XRV series: Start-up, operation and maintenance instructions Start-up and service instructions Installation instructions Start-up, operation and maintenance instructions Start-up and service instructions

Contents

57CHANGE THE BENSHAW INC., RediStart MICRO™SOFTWARE CONFIGURATION IF NECESSARY — Ben-shaw starter configurations are checked and modified from themenus in the Benshaw Redistart MICRO Default Display. SeeFig. 32 and Table 6 for default display and menu items. To ac-cess the menus to perform checks and modifications, the Ben-shaw starter must be powered up and its self-test must havebeen successfully completed. The self-test takes place automat-ically after power-up. Current transformer ratio configurationsand hardware switch settings checks are performed in theMENU1 display screen. See Table 7 for menu structure andTable 8 for switch settings.1. Press the softkey until the desired menu is se-lected on the display.2. Press the softkey to access the displayed menuitems (Table 6).3. Use the or arrow keys to scroll between menuitems until the desired item is reached on the display.4. Press the softkey to access the value to bechanged.5. Use the or arrow keys to adjust the new displayedvalue. The key increases the value while the keydecreases the value. Holding the arrow key will progres-sively increase the rate of change. The value will stopchanging when either the factory set minimum or maxi-mum value is reached. To make fine adjustments pressand release the arrow key.6. When the correct value has been selected, press thekey to store the new configuration. At thispoint, there are two options. The key will returnthe display to the main display. The or arrow keyswill move the display to the next menu item. When fin-ished press the key to return to the main display.To view other settings and troubleshooting guide consult theBenshaw RediStart MICRO instructional manual included inthe starter.Table 6 — Benshaw RediStartMICRO Menu StructureTable 7 — Benshaw RediStart MICRO Menu Items**These values are not displayed in the ISM_CONFIG table.Table 8 — Benshaw RediStart MICRO Current Transformer DIP Switch SettingsLEGENDCT — Current TransformerMENUENTER↓ ↑ENTER↑ ↓↑ ↓ENTERMENU↑ ↓MENUMENU 1Starter SetupMENU 2Meter SetupMENU 3EventRecorderMENU 4Dry RunModeInitial Currentas % RLAMeter #1displayEvents 1-99 Dry RunModeMax. CurAs% LRAMeter #2displayRamp Time(sec.)CT Ratio: 1DESCRIPTION RANGE UNITS DEFAULTINITIAL CURRENT 50-300 % 125MAX. CURR AS % LRA 30-70 % 55RAMP TIME 5-30 SEC 15CT RATIO 2640-5760 Enter Value from Table 8.CURRENT TRANSFORMER CT1-CT3StarterFrame Size(Amps)MotorRLA Range(Amps)CTRatioMIcro Power Card (BIPCMIPWR-C4)Overload Switch SettingsSW1-1 SW1-2200 Amps 95- 135 Amps 3900:1 OFF OFF136- 200 Amps 5760:1 OFF OFF300 Amps 201- 231 Amps 2640:1 ON OFF232- 300 Amps 3900:1 ON OFF480 Amps 301- 340 Amps 3900:1 ON OFF341- 480 Amps 5760:1 ON OFF600 Amps 481- 580 Amps 2640:1 ON ON581- 600 Amps 3900:1 ON ON740 Amps 601- 740 Amps 3900:1 ON ON1250 Amps 741- 855 Amps 3900:1 ON ON856-1250 Amps 5760:1 ON ONFAULTRESETMENU ENTERDISPLAYSCROLL UPSCROLL DOWNMENUSELECTION MENU ENTRYDATA ENTRYSTOP I = OAREADY V = 461VRediStart MICROFig. 32 — Benshaw RediStartMICRO Default Display