Carrier 40GXC Owner's Manual

Also see for 38GXC: Installation instructions Owner's manual Product data Service manual

Contents

9Selecting the Horizontal Direction Louver PositionWhen the unit is turned on, the louvers default to the cooling orheating position.If the louver position is not providing adequate comfort due toroom layout or where people are gathered, two options areavailable to correct the situation:Setting the louvers in a stationary position(other than default for heating and cooling):The stationary position can be one of five (5) default positions ora position selected by user.To change the louver position, press the “SWING“ buttononce. The icon is displayed on the remote.OPERºFºCHOURON/OFF:A09640When the is displayed, the louver will swing continuouslybetween positions 1 and 5 as shown below.OFF0 1 2 3 45678A09634If the “SWING” button is pushed again, the horizontallouver will stop at the position it was in when the buttonwas pressed. If position 1 through 5 is desired, push thebutton repeatedly until the desired position (1 through 5) isdisplayed on remote control.Setting the lovers to move continuously:This setting allows the louvers to move continuously betweeneither positions 1 through 5, or between positions 6, 7, and 8.Push the button once to have louvers swinging betweenpositions 1 and 5. If position 6, 7, or 8 is desired, push thebutton repeatedly until the desired position is displayed on theremote.NOTE: Always use the remote control to adjust the horizontallouver position otherwise, abnormal operation may occur. Ifthis occurs, turn the unit off and then on again.Sometimes, in the heating mode, when the ”SWING”button is pushed, the louvers will not start moving right away.This is due to the fact that the fan will not start running untilthe coil temperature is warm enough to prevent discomfort tothe user by blowing cold air.Selecting Vertical Direction of the LouverThe vertical louvers can be adjusted manually to direct the airflowto achieve the optimal comfort in the space.A07543Timer FunctionTIMER ON (to start the unit) and TIMER OFF (to stop the unit)can be used separately or together. The clock on the remote controlmust be set before using this function.Timer ON onlyºFºCHOUR:OPEROnly ONis displayed.ONA09639This function will allow the unit to start automatically at the settime. The TIMER ON can be set while the unit is on or off.To set the TIMER ON function, perform the following:1. Push the “TIMER ON” button once.2. The clock indicator and time will not be displayed onthe remote control. The default “TIMER ON” time (firsttime function is used) or the last time setting will be dis-played and “ON” will flash.3. Push the “--” or “+” within 5 seconds until the desired ontime is displayed.NOTE: Pressing the “--” or “+” will decrease or increase thetime in 1 minute increments.Pressing the “--” or “+” continuously will decrease or increasethe time in 10 minute increments.4. Push the “TIMER ON” again. The “ON” icon will stopblinking and the time at which the unit will start is set. Theclock indicator and the time will be displayed again.The “TIMER ON” time will be stored in memory indefinitely untilit is cancelled by the user by pushing the “TIMER ON” button orthe remote control batteries are replaced.If the unit is running and the “TIMER ON” set time is reached, theunit will continue operating normally.NOTE: When the unit is shut off by the user using the“ON/OFF” button, and if the “TIMER ON” is set, thefollowing will be displayed on the remote control.-- Set Point-- Time-- Clock indicator next to time indicates TIMER ON is set.On the display panel, the operation light will turn red.When the “TIMER ON” set time is reached, the display on theremote does not change, but the unit will run as indicated bythe operation light on the front cover turning green. To getdisplay on the remote, push the “ON/OFF” button once.

/ 12

Related manuals for Carrier 38GXC