Carrier 50HJQ004-016 Product Data

Also see for APOLLO CONTROL 50HJQ004-016: Installation, operating and troubleshooting instructions

125ELECTRICAL DATA — 50HJQ (CONT)50HJQ004-012 — STANDARD MOTOR UNITS WITH ELECTRICAL CONVENIENCE OUTLET (CONT)UNIT50HJQNOMINALVOLTAGE(V-Ph-Hz)VOLTAGERANGECOMPRESSOR(each)OFM(each) IFM ELECTRIC HEAT* POWER SUPPLYMINIMUM UNITDISCONNECTSIZE50HJQ (V-Ph-Hz) Min Max RLA LRA FLA FLA kW† FLA MCA MOCP** FLA LRA008208/230-3-60 187 254 12.4 88.0 1.4 7.5—7.8/10.412.0/16.018.6/24.824.0/32.031.8/42.4—21.7/ 25.033.3/ 38.551.6/ 59.766.6/ 77.088.3/102.043.0/ 43.070.1/ 74.384.6/ 91.1107.5/117.6126.3/139.3153.4/170.545/ 4580/ 8090/100110/125150/150175/17546/ 4671/ 7584/ 90105/115122/134147/163247/247269/272280/285††298/307††313/324††335/349††008(71 /2 Tons)460-3-60 414 508 6.4 44.0 0.7 3.4—13.916.527.833.041.7—16.719.833.439.750.221.442.346.163.171.084.1254550708090234246616880123140143157163174— — 46.1/ 46.1 50/ 50 49/ 49 281/2817.8/10.4 21.7/ 25.0 73.2/ 77.3 80/ 80 74/ 78 303/306208/230 3 60 187 254 13 9 105 1 4 7 5 12.0/16.0 33.3/ 38.5 87.7/ 94.2 90/100 87/ 93 314/319††208/230-3-60 187 254 13.9 105 1.4 7.5 18.6/24.8 51.6/ 59.7 110.6/120.7 125/125 108/118 332/341††009 24.0/32.0 66.6/ 77.0 129.3/142.3 150/150 126/138 347/358††009 31.8/42.4 88.3/102.0 156.5/173.6 175/175 151/166 369/383††(81 /2 Tons) — — 24.5 25 26 145(81 /2 Tons) 13.9 16.7 45.3 50 45 162460 3 60 414 508 7 9 55 0 0 7 3 4 16.5 19.8 49.2 50 49 165460-3-60 414 508 7.9 55.0 0.7 3.4 27.8 33.4 66.2 70 64 17933.0 39.7 74.1 80 72 18541.7 50.2 87.2 90 84 196012208/230-3-60 187 254 19.3 123.0 1.4 10.6—7.8/10.412.0/16.024.0/32.031.8/42.437.6/50.0—21.7/ 25.033.3/ 38.566.6/ 77.088.3/102.0104.4/120.361.6/ 61.688.8/ 92.9103.3/109.8144.9/157.9172.0/189.1192.1/181.970/ 7090/100110/110150/175175/200200/20065/ 6590/ 94104/110142/154167/183185/204341/341363/366††375/380††408/418††430/443††446/462††012(10 Tons)460-3-60 414 508 10.0 62.0 0.7 4.8—16.527.833.041.750.0—19.833.439.750.260.130.955.672.680.593.691.0356080901001003355717890102172191205211222††232††LEGENDFLA — Full Load AmpsHACR — Heating, Air Conditioning and RefrigerationIFM — Indoor Fan MotorLRA — Locked Rotor AmpsMCA — Minimum Circuit AmpsMOCP — Maximum Overcurrent ProtectionNEC — National Electrical CodeOFM — Outdoor Fan MotorRLA — Rated Load Amps*Heater capacity (kW) is based on heater voltage of 208 v, 240 v and 480 v.If power distribution voltage to unit varies from rated heater voltage, heat-er kW will vary accordingly.{Heaters are field installed only.**Fuse or HACR circuit breaker.{{Electrical disconnect cannot be used if electric heater is installed.NOTES:1. In compliance with NEC requirements for multimotor and combinationload equipment (refer to NEC Articles 430 and 440), the overcurrent pro-tective device for the unit shall be fuse or HACR breaker.2. Unbalanced 3-Phase Supply VoltageNever operate a motor where a phase imbalance in supply voltage isgreater than 2%. Use the following formula to determine the percent ofvoltage imbalance.% Voltage Imbalancemax voltage deviation from average voltage= 100 x average voltageExample: Supply voltage is 460-3-60.AB = 452 vBC = 464 vAC = 455 v452 + 464 + 455Average Voltage = 31371= 3= 457Determine maximum deviation from average voltage.(AB) 457 – 452 = 5 v(BC) 464 – 457 = 7 v(AC) 457 – 455 = 2 vMaximum deviation is 7 v.Determine percent of voltage imbalance.% Voltage Imbalance = 100 x 7457= 1.53%This amount of phase imbalance is satisfactory as it is below the maxi-mum allowable 2%.IMPORTANT:If the supply voltage phase imbalance is morethan 2%, contact your local electrical utility companyimmediately.POWER EXHAUST ELECTRICAL DATAPOWER EXHAUSTPART NO.APPLICATIONUSAGEMCA(230v)MCA(460v)MCA(575v)MOCPseparatepowersource only)CRPWREXH030A01 004--- 007* 1.6 N/A 0.64 15CRPWREXH021A01 004--- 007* N/A 0.68 N/A 15CRPWREXH022A01 008--- 014* 3.4 N/A 1.32 15CRPWREXH023A01 008--- 014* N/A 1.4 N/A 15CRPWREXH028A01 ALL 1.7 N/A 0.68 15CRPWREXH029A01 ALL N/A 0.7 N/A 15* Single or three phaseN/A — Not availableNOTE: If a single power source is to be used, size wire to include power exhaustMCA and MOCP.Check MCA and MOCP when power exhaust is powered through the unit. Deter-mine the new MCA including the power exhaust using the following formula:MCA New = MCA unit only + MCA of Power ExhaustFor example, using a 50TFQ006---5 unit with MCA = 35.6 and MOCP = 40, withCRPWREXH030A01 power exhaust.MCA New = 35.6 amps + 1.6 amps = 37.2 ampsIf the new MCA does not exceed the published MOCP, then MOCP would notchange. The MOCP in this example is 40 amps and the MCA New is below 40;therefore the MOCP is acceptable. If “MCA New” is larger than the publishedMOCP, raise the MOCP to the next larger size. In all cases, the MOCP for the pow-er exhaust should be 15 amps per NEC.50HJQ