Carrier RTU OPEN 11-808-427-01 Installation And Startup Manual Manual pdf 11 page image
Manuals database logo
manualsdatabase
Your AI-powered manual search engine

Carrier RTU OPEN 11-808-427-01 Installation And Startup Manual

Also see for RTU - OPEN: Controls, Start-Up, Operation and Troubleshooting InstructionsControls, Start-Up, Operation and Troubleshooting

Page 1 previewPage 2 previewPage 3 previewPage 4 previewPage 5 previewPage 6 previewPage 7 previewPage 8 previewPage 9 previewPage 10 previewPage 11 previewPage 12 previewPage 13 previewPage 14 previewPage 15 previewPage 16 previewPage 17 previewPage 18 previewPage 19 previewPage 20 previewPage 21 previewPage 22 previewPage 23 previewPage 24 previewPage 25 previewPage 26 previewPage 27 previewPage 28 previewPage 29 previewPage 30 previewPage 31 previewPage 32 previewPage 33 previewPage 34 previewPage 35 previewPage 36 previewPage 37 previewPage 38 previewPage 39 previewPage 40 previewPage 41 previewPage 42 previewPage 43 previewPage 44 previewPage 45 previewPage 46 previewPage 47 previewPage 48 previewPage 49 previewPage 50 previewPage 51 previewPage 52 previewPage 53 previewPage 54 previewPage 55 previewPage 56 previewPage 57 previewPage 58 previewPage 59 previewPage 60 previewPage 61 previewPage 62 previewPage 63 previewPage 64 previewPage 65 previewPage 66 previewPage 67 previewPage 68 previewPage 69 previewPage 70 previewPage 71 previewPage 72 previewPage 73 previewPage 74 previewPage 75 previewPage 76 previewPage 77 previewPage 78 previewPage 79 previewPage 80 previewPage 81 previewPage 82 previewPage 83 previewPage 84 preview
Contents
  1. Table Of Contents
  2. Table Of Contents
  3. Table Of Contents
  4. What is the RTU Open controller
  5. Specifications
  6. Safety considerations
  7. Field-supplied hardware
  8. To mount the RTU Open
  9. To wire the controller for power
  10. Using an auxiliary control power transformer
  11. To set the RTU Open's address
  12. To set the RTU Open's communications protocol and baud rate
  13. Wiring specifications
  14. Wiring inputs and outputs
  15. Input wiring specifications
  16. Binary outputs
  17. compressor safety
  18. additional functions
  19. Wiring sensors to inputs
  20. Field-supplied sensor hardware
  21. Wiring an SPT sensor
  22. To wire the SPT sensor to the controller
  23. To wire the SAT sensor to the controller
  24. To wire a duct sensor to the controller
  25. Wiring a CO2 sensor
  26. Wiring an Outdoor Air Quality sensor
  27. To wire the OAQ sensor to the controller
  28. To wire the RH sensor to the controller
  29. To wire a humidistat to the controller
  30. To wire an enthalpy switch (outdoor air) to the controller
  31. To wire an enthalpy switch (differential) to the controller
  32. Wiring a status switch
  33. To wire a status switch to the controller
  34. To wire a compressor safety input to the controller
  35. To wire an occupancy switch or door contact
  36. Start-up
  37. Service Test
  38. Configuring the RTU Open's properties
  39. Setpoint properties
  40. Service Configuration properties
  41. Occupancy
  42. Supply fan
  43. Economizer
  44. Unoccupied Free Cooling
  45. Enthalpy control
  46. Heating
  47. Heat Pump operation
  48. Demand Limit
  49. Fan Status
  50. Linkage
  51. Linkage Air Source Modes
  52. Serial number
  53. Replacing the RTU Open's battery
  54. FCC Compliance
  55. Status
  56. Unit Configuration
  57. Setpoints
  58. Alarm Configuration
  59. Service Configuration
  60. Maintenance
  61. Alarms
  62. I/O Points
  63. Appendix B: Single Point Linkage and Device Address Binding
  64. Device Address Binding
  65. Index
Carrier RTU OPEN 11-808-427-01 Installation And Startup Manual Manual pdf 11 page image
RTU Open 5To install the RTU Open:1 Mount the controller (page 6).2 Wire the controller for power (page 7).○ Using the rooftop equipment control power transformer (page 7).○ Using an auxiliary control power transformer (page 8).3 Set the controller's address (page 9).4 Wire inputs and outputs (page 12).5 Wire sensors to the controller (page 18).Field-supplied hardwareAn RTU Open retrofit installation may require the following field-supplied components:• wiring harness: Part #OPN-RTUHRN• transformer – 24 Vac, 20 VA minimum• wiringApplication-dependent components:• carbon dioxide sensors• damper/damper actuator• differential pressure switch• enthalpy switch• fan status switch• door switch• fan section door switch• relative humidity sensor• remote occupancy contact• smoke detector• temperature sensorsInstallation
/ 84
Related manuals for Carrier RTU - OPEN
Carrier RTU Open v5 Installation And Startup Manual first page preview
Carrier RTU Open v5 Installation And Startup Manual
Carrier RTU Open v3 Installation And Startup Manual first page preview
Carrier RTU Open v3 Installation And Startup Manual
Carrier UC Open Installation And Startup Manual first page preview
Carrier UC Open Installation And Startup Manual
Carrier UC Open XP Installation And Startup Manual first page preview
Carrier UC Open XP Installation And Startup Manual
Carrier UC Open XP Installation And Startup Manual first page preview
Carrier UC Open XP Installation And Startup Manual
Carrier i-Vu Open Link Installation And Startup Manual first page preview
Carrier i-Vu Open Link Installation And Startup Manual
Carrier OPN-OPT-OL Installation And Startup Manual first page preview
Carrier OPN-OPT-OL Installation And Startup Manual
Carrier MPC Open XP Series Installation And Startup Manual first page preview
Carrier MPC Open XP Series Installation And Startup Manual
Carrier i-Vu MPC Open XP IO48/816 Installation And Startup Manual first page preview
Carrier i-Vu MPC Open XP IO48/816 Installation And Startup Manual
Carrier ChillerVu Installation And Startup Manual first page preview
Carrier ChillerVu Installation And Startup Manual
This manual is suitable for:
RTU - OPENRTU OPEN 11-808-427-01
Manuals database logo
manualsdatabase
Your AI-powered manual search engine