Danfoss VLT Aqua Drive FC 202 Operating Manual

Also see for VLT AQUA Drive FC 202: Service guide Installation guide Installation guide Operating guide Installation guide

Contents

Type designation P37K P45K P55K P75K/N75K8) P90K/N90K8)High/normal overload1) HO NO HO NO HO NO HO NO HO NOTypical shaft output at 550 V [kW] 22 30 30 37 37 45 45 55 55 75Typical shaft output at 550 V [hp] 30 40 40 50 50 60 60 75 75 100Typical shaft output at 690 V [kW] 30 37 37 45 45 55 55 75 75 90Typical shaft output at 690 V [hp] 40 50 50 60 60 75 75 100 199 125IP20/Chassis B4 C3 C3 D3h D3hIP21/Type 1IP55/Type 12 C2 C2 C2 C2 C2Output currentContinuous (3x525–550 V) [A] 36.0 43.0 43.0 54.0 54.0 65.0 65.0 87.0 87.0 105Intermittent (60 s overload) (3x525–550 V) [A] 54.0 47.3 64.5 59.4 81.0 71.5 97.5 95.7 130.5 115.5Continuous (3x551–690 V) [A] 34.0 41.0 41.0 52.0 52.0 62.0 62.0 83.0 83.0 100Intermittent (60 s overload) (3x551–690 V) [A] 51.0 45.1 61.5 57.2 78.0 68.2 93.0 91.3 124.5 110Continuous kVA at 550 V [kVA] 34.3 41.0 41.0 51.4 51.4 61.9 61.9 82.9 82.9 100Continuous kVA at 690 V [kVA] 40.6 49.0 49.0 62.1 62.1 74.1 74.1 99.2 99.2 119.5Maximum input currentContinuous at 550 V [A] 36.0 49.0 49.0 59.0 59.0 71.0 71.0 87.0 87.0 99.0Intermittent (60 s overload) at 550 V [A] 54.0 53.9 72.0 64.9 87.0 78.1 105.0 95.7 129 108.9Continuous at 690 V [A] 36.0 48.0 48.0 58.0 58.0 70.0 70.0 86.0 – –Intermittent (60 s overload) at 690 V [A] 54.0 52.8 72.0 63.8 87.0 77.0 105 94.6 – –Additional specificationsMaximum cable cross-section for mains andmotor [mm2 (AWG)] 150 (300 MCM)Maximum cable cross-section for brake andload sharing [mm2 (AWG)] 95 (3/0)Maximum cable cross-section2) for mainsdisconnect [mm2 (AWG)] 95 (3/0)185, 150, 120(350 MCM, 300MCM, 4/0)–Estimated power loss3)at rated maximum load [W (hp)]4)600(0.82) 740 (1) 740 (1) 900(1.2)900(1.2)1100(1.5)1100(1.5)1500(2)1500(2)1800(2.5)Efficiency5) 0.98 0.98 0.98 0.98 0.98Table 8.17 B4, C2, C3 Enclosure, Mains Supply 3x525–690 V AC IP20/IP21/IP55 – Chassis/NEMA1/NEMA 12, P30K–P75KFor fuse ratings see chapter 8.8 Fuses and Circuit Breakers.1) High overload=150% or 160% torque for a duration of 60 s. Normal overload=110% torque for a duration of 60 s.2) The 3 values for the maximum cable cross-section are for single core, flexible wire, and flexible wire with sleeve, respectively.3) Applies for dimensioning of frequency converter cooling. If the switching frequency is higher than the default setting, the power losses mayincrease. LCP and typical control card power consumptions are included. For power loss data according to EN 50598–2, refer towww.danfoss.com/vltenergyefficiency.4) Efficiency measured at nominal current. For energy efficiency class see chapter 8.4.1 Ambient Conditions. For part load losses seewww.danfoss.com/vltenergyefficiency.5) Measured using 5 m (16 ft) shielded motor cables at rated load and rated frequency.6) Enclosure sizes A2+A3 can be converted to IP21 using a conversion kit. See also chapters Mechanical mounting and IP21/Type 1 Enclosure kit inthe design guide.7) Enclosure sizes B3+B4 and C3+C4 can be converted to IP21 using a conversion kit. See also chapters Mechanical mounting and IP21/Type 1Enclosure kit in the design guide.8) Enclosure sizes for N75K, N90K are D3h for IP20/Chassis, and D5h for IP54/Type 12.9) Two wires are required.10) Variant not available in IP21.Specifications Operating GuideMG20MD02 Danfoss A/S © 10/2016 All rights reserved. 638 8