DeLonghi ESAM 04.320 Owner's Manual

Contents

9PRElIMINARY CHECKSChecking the applianceafter removing the packaging, make sure the product iscomplete and undamaged and that all accessories are present.do not use the appliance if it is visibly damaged. Contactde’longhi Customer Services.Installing the applianceImportant!When you install the appliance, you should respect thefollowing safety warnings:• The appliance gives off heat. After positioning theappliance on the worktop, leave a space of at least 3 cmbetween the surfaces of the appliance and the side andrear walls and at least 15 cm above the coffee maker.• Water penetrating the appliance could cause damage. Donot place the appliance near taps or sinks.• The appliance could be damaged if the water it containsfreezes. do not install the appliance in a room where thetemperature could drop below freezing point.• Arrange the power cable in such a way that it cannot bedamaged by sharp edges or contact with hot surfaces(e.g. electric hot plates).Connecting the applianceImportant!Check that the mains power supply voltage corresponds tothe value indicated on the rating plate on the bottom of theappliance.Connect the appliance to an efficiently earthed and correctlyinstalled socket with a minimum current rating of 10a only.if the power socket does not match the plug on the appliance,have the socket replaced with a suitable type by a qualifiedprofessional.Using the appliance for the first timePlease note :• Coffee has been used to factory test the appliance and it istherefore completely normal for there to be traces of coffeein the grinder. The machine is, however, guaranteed to benew.• You should customise water hardness as soon as possiblefollowing the instructions in the section “Setting waterhardness” on page 16.1. Plug the appliance into the mains socket and place themain switch on the back of the appliance in the i position(fig. 1).you must first choose the language (the languages scrollthrough at intervals of about 3 seconds).2. When “english” appears, press the OK button (fig. 2) for afew seconds until “eNgliSh set” is displayed.Follow the instructions indicated by the appliance:3. “FILL TANK”: remove the water tank, fill to the MAX linewith fresh water then replace in the appliance (fig. 3).4. Turn the cappuccino maker outwards and place a containerwith a minimum capacity of 100 ml underneath (fig. 4).5. “TURN STEAM KNOB” is displayed. When the steam knobis turned to the I position (fig. 4), “Hot water Press OK” isdisplayed.6. Press the OK button (fig. 2).“Please wait” is displayed and the appliance begins todeliver water from the hot water spout.The appliance ends the first start up procedure, then themessage “Turning off, Please wait” is displayed and theappliance goes off.The coffee maker is now ready for normal use.Please note:• When using the appliance for the first time, you need tomake 4-5 cups of coffee or 4-5 cappuccinos before theappliance starts to give satisfactory re-sults.TURNING THE APPlIANCE ONPlease note:Before turning the appliance on, make sure the main switch onthe back of the appliance is in the i position (fig. 1).each time the appliance is turned on, it performs an automaticpreheat and rinse cycle which cannot be interrupted.The appliance is ready for use only after completion of thiscycle.Danger of burns!during rinsing, a little hot water comes out of the coffee spoutsand is collected in the drip tray underneath.avoid contact with splashes of water.• To turn the appliance on, press the button (fig. 5).The message “heating up, Please wait” is displayed.after heating, the message “rinsing” is displayed. as well asheating the boiler, the appliance also heats the internal circuitsby circulating hot water.The appliance is at temperature when the message indicatingthe taste and quantity of coffee appears.TURNING THE APPlIANCE OFFeach time the appliance is turned off, it performs an automaticrinse cycle which cannot be interrupted.