DeLonghi ESAM 04.320 Owner's Manual

Contents

161. accendere la macchina.2. Press the MENU button to enter the settings menu. Pressthe or button until “descale” is displayed;3. Press the OK button. “descale Confirm?” is displayed. PressOK to enable the function.4. The message “Add descaler Press OK” is displayed.5. Before confirming, empty the water tank (a13).Pour the descaler diluted with water (respecting theproportions indicated on the descaler pack) into the watertank and replace the tank in the appliance.6. Place an empty container with a minimum capacity of 1.5litres under the hot water spout.Important! Danger of burnshot water containing acid flows out of the hot water spout.avoid contact with splashes of water.7. Confirm with the OK button.8. “TURN STEAM KNOB” is displayed.9. after turning the knob to the I position (fig. 4), “descalePress OK” is displayed.10. after confirming by pressing OK, the message “descaleunderway” is displayed.The descale programme starts and the descaler liquidcomes out of the water spout.The descale programme automatically performs a seriesof rinses and pauses to remove limescale deposits frominside the machine.After about 30 minutes, “TURN STEAM KNOB” is displayed.When the steam knob is turned to the 0 position, “rinsing FillTANK” is displayed.11. The appliance is now ready for rinsing through withclean water. remove the water tank, empty, rinse underrunning water, fill with clean water and replace. “TurNSTEAM KNOB” is displayed. When the steam knob isturned to the I position, “Rinsing... Press OK” is displayed.12. empty the container used to collect the descaler solutionand replace it under the hot water spout.13. Press the OK button to start rinsing. hot water flows outof the spout and the message “rinsing... Please wait” isdisplayed.14. When the water tank is completely empty, “TurN STeaMKNOB” is displayed.15. When the steam knob is turned to the 0 position, theappliance goes off.To use it again, turn the appliance on by pressing thebutton.SETTING WATER HARDNESSThe deSCale message is displayed after a period of timeestablished according to water hardness.The machine is set by default for a hardness value of 4 (veryhard water).The machine can also be programmed according to the actualhardness of the mains water in the various regions, varying thefrequency with which the message is displayed.Measuring water hardness1. remove the “ToTal hardNeSS TeST” indicator paper fromits pack.2. immerse the paper completely in a glass of water for onesecond.3. remove the paper from the water and shake lightly. afterabout a minute, 1, 2, 3, or 4 red squares form, dependingon the hardness of the water. each square corresponds toone level.level 1 - soft water llevel 2 - slightly hard waterlllevel 3 - hard waterllllevel 4 - very hard waterllllSet water hardness1. Press the MENU button to enter the settings menu.2. Press the or button and select “Water hardness”.3. Confirm the selection by pressing the OK button.4. Press the or button to set the water hardnessidentified using the indicator paper (see figure in theprevious section).5. Press the OK button to confirm the setting.6. Press the ESC button to exit the menu.The machine is now reprogrammed with the new waterhardness setting.TECHNICAl SPECIFICATIONvoltage: 220-240 v~ 50/60 hz max. 10aabsorbed power: 1350WPressure: 15 barWater tank capacity: 1,7 lSize: lxhxd: 282x374x441 mmCable length: 1,5 mWeight: 11,4 KgMax. beans container capacity 250 g• S• La• Ea• McDISPspeciato a dappliafor thdisposto obreminseparadustbi

/ 21

Related manuals for DeLonghi ESAM 04.320