Delta DT3 Series Instruction Sheet
6Initial Start-up Setting1. When setting up DT3 for the first time, press key for more than 3 seconds till the screen display and select accordingto your temperature sensor type. Please be aware that a selection of wrong model would cause PV temperature display error. (Referto the chart below)2. When setting up the temperature sensor type by using RS-485, write your value (range 0~19) into register 1004H.3. When setting up the current input method, remove the temperature controller cover and set JP8 to short. (Refer to the chart below)z Temperature Sensor Type & Temperature Range ChartInput TemperatureSensor Type Register Value Temperature Range Input Temperature Sensor Type Register Value Temperature RangeThermocouple K type 0 -200 ~ 1300°C Thermocouple TXK type 10 -200 ~ 800°CThermocouple J type 1 -100 ~ 1200°C Platinum Resistance (JPt100) 11 -20 ~ 400°CThermocouple T type 2 -200 ~ 400°C Platinum Resistance (Pt100) 12 -200 ~ 850°CThermocouple E type 3 0 ~ 600°C Platinum Resistance (Ni120) 13 -80 ~ 300°CThermocouple N type 4 -200 ~ 1300°C Platinum Resistance (Cu50) 14 -50 ~ 150°CThermocouple R type 5 0 ~ 1700°C Analog Voltage Input (0~5V) 15 -999~9999Thermocouple S type 6 0 ~ 1700°C Analog Voltage Input (0~10V) 16 -999~9999Thermocouple B type 7 100 ~ 1800°C Analog Voltage Input (0~20m A) 17 -999~9999Thermocouple L type 8 -200 ~ 850°C Analog Voltage Input (4~20m A) 18 -999~9999Thermocouple U type 9 -200 ~ 500°C Analog Voltage Input (0~50m V) 19 -999~9999z How to Set Up Current InputRemove the temperature controller cover and set JP8 to short. JP8 jumper locates near the sensor input area on PCB board.Normal Iniput (Factory Setting) Current Input (4 ~ 20mA, 0 ~ 20mA)Display Unit SettingUse following parameter to change the PV and SV display unit, select decimal point and switch between ℃/F.¾ In Operation Mode : SP=1 displays decimal place (ex: 25.5 degree); SP=0 displays integral number (ex: 25 degree).¾ In Initial Setting Mode : Select temperature display unit ℃/℉. (℉=℃* 9 / 5 + 32)Set Value and the Upper/Lower Limit of Input Value Setting¾ Set the Upper Limit of Input Value: This parameter can be set in the Initial Setting Mode , the upper limit input value mustbe set within the range shown in the chart “Temperature Sensor Type & Temperature Range”.¾ Set the Lower Limit of Input Value: This parameter can be set in Initial Setting Mode , the lower limit input value must beset within the range shown in the chart “Temperature Sensor Type & Temperature Range”.¾ Set the SV: This parameter can be set in Operation Mode, SV value must be set within the range of upper/lower limit input value.SV can not be set in In “Program Mode” or in “Remote Mode”.Digital Filter and Linear Compensation SettingIn “Regulation Mode”, and parameters can be used to ajust the filter status and to avoid interferences on input signal.¾ : Filter Factors (setting range=0~50; factory setting=8). Digital Filter Calculation equation: PV=(Last displayed PV * n +Measure Value)/ (n+1). When the parameter value is small, the PV display is close to the Measured Value. When the parametervalue is large, the PV response is slow.¾ : Filter Range (setting range=0.10~10.00℃/℉). If factory setting = 1, it means the controller will begin Digital FilterCalcaulation when the Measure Value lies within the range of “Last displayed PV + / - 1.00℃/℉”. Therefore, it is recommended toset a larger value when noise interferences is serious.When PV display value is different than user’s expectation, Linear Compensation function can be set by andparameters in“Regulation Mode”.¾ : Linear Compensation Value (setting range= -99.9 ~ +99.9). Linear Compensation Calculation equation: PV = MeasureValue + Compensation Value. |
Related manuals for Delta DT3 Series
Delta DTD Series Instruction Sheet
Delta DVP-MC Series Instruction Sheet
Delta DVP-EH Series Instruction Sheet
Delta DVP-EH2 Series Instruction Sheet
Delta ASDA-A2 Series Instruction Sheet
Delta DVP-SA Instruction Sheet
Delta DVP-SS Instruction Sheet
Delta DVP-SA2 Instruction Sheet
Delta DVP-EH Instruction Sheet
Delta DVP-SS2 Instruction Sheet
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine