Denon AVR-1705 Operating Instructions Manual

Also see for AVR-1705: Operating instructions Product sheet Service manual Service manual Operating instructions

Contents

Denon AVR-1705 Operating Instructions Manual Manual pdf 10 page image

10ENGLISHSETTING UP THE SYSTEM• Once all connections with other AV components have been completed as described in “CONNECTIONS” (seepages 6 to 9), make the various settings described below on the display.These settings are required to set up the listening room’s AV system centered around the this unit.SYSTEM SETUP buttonPress this to display the system setup on the display.ENTER buttonPress this to switch the display.Also use this button to complete the setting.CURSOR buttons (•, ª, 0, 1)Press this change what appears on the display.102 Use the following buttons to set up the system:1 Set the slide switch to “AUDIO”.• System setup items and default values (set upon shipment from the factory)System setup Default settingsSpeakerConfigurationSubwooferModeDigital InAssignmentInput the combination of speakers in yoursystem and their corresponding sizes (SMALLfor regular speakers, LARGE for full-size, full-range) to automatically set the composition ofthe signals output from the speakers and thefrequency response.This selects the subwoofer speaker for playingdeep bass signals.This assigns the digital input jacksfor the different input sources. DigitalInputsInputsourceFront Sp.LargeCenterSp.SurroundSp.SurroundBack Sp.Small Small SmallSubwoofer mode = NormalFrontL Center3.6 m 3.6 mCD DVD/VDPCOAXIAL OPTICAL 1Delay TimeThis parameter is for optimizing the timing withwhich the audio signals are produced from thespeakers and subwoofer according to thelistening position.SubwooferYesCrossoverFrequencySet the frequency (Hz) below which the basssound of the various speakers is to be outputfrom the subwoofer.80 HzFrontR3.6 mSurroundL3.0 mSurroundR3.0 mSurroundBack3.0 mSubwoofer3.6 mFrontL Center0 dB 0 dBTest ToneThis adjusts the volume of the signals outputfrom the speakers and subwoofer for thedifferent channels in order to obtain optimumeffects.FrontR0 dBSurroundL0 dBSurroundR0 dBSurroundBack0 dBSubwoofer0 dBTV/DBSOPTICAL 2Ext. In SWLevel Set the Ext. In Subwoofer channel playback level. Ext. In SW Level = +15 dBAuto SurroundMode Auto surround mode function setting. Auto Surround Mode = ONPoint the remote control unit at the remote controlsensor as shown on the diagram at the left.NOTES:• The remote control unit can be used from a straightdistance of approximately 7 meters, but this distancewill shorten or operation will become difficult ifthere are obstacles between the remote control unitand the remote control sensor, if the remote controlsensor is exposed to direct sunlight or other stronglight, or if operated from an angle.• Neon signs or other devices emitting pulse-typenoise nearby may result in malfunction, so keep theset as far away from such devices as possible.Approx. 7 m30°30°Range of operation of the remote control unitUSING THE REMOTE CONTROL UNITFollowing the procedure outlined below, insert the batteries before using the remote control unit.Inserting the batteriesq Press as shown by the arrowand slide off.w Insert the R6P/AA batteries properly,as shown on the diagram.e Close the lid.NOTES:• Use only R6P/AA batteries for replacement.• Be sure the polarities are correct. (See the illustration inside the battery compartment.)• Remove the batteries if the remote control transmitter will not be used for an extended period of time.• If batteries leak, dispose of them immediately. Avoid touching the leaked material or letting it come in contactwith clothing, etc. Clean the battery compartment thoroughly before installing new batteries.• Have replacement batteries on hand so that the old batteries can be replaced as quickly as possible when thetime comes.• Even if less than a year has passed, replace the batteries with new ones if the set does not operate even whenthe remote control unit is operated nearby the set. (The included battery is only for verifying operation. Replaceit with a new battery as soon as possible.)9NOTE:• The system setup is not displayed when “HEADPHONE ONLY” is selected.