ENGLISH34Symptom Cause Measures PageRemote control unitThis unit does not operateproperly when remote controlunit is used.• Batteries dead.• Remote control unit too far fromthis unit.• Obstacle between this unit andremote control unit.• Different button is being pressed.• < and > ends of battery inserted inreverse.• Replace with new batteries.• Move closer.• Remove obstacle.• Press the proper button.• Insert batteries properly.999—9NOTE:When a subwoofer has been connected and the virtual surround function is being used, the signal played fromthe subwoofer channel is LFE only (only when playing Dolby Digital or DTS signals) for initial factory settings(i.e., the setting of the front speaker is “LARGE” and the setting of the subwoofer mode is “NORM”).When subwoofer effects are felt to be weak, try setting the subwoofer mode to “+MAIN”, or the frontspeaker to “SMALL” in the System setup ”Speaker Configuration” settings.Making these settings will result in the low-frequency sounds of the front channel being played from thesubwoofer.2 Audio section• Power amplifierRated output: Front: 80 W + 80 W (8 Ω/ohms, 20 Hz ~ 20 kHz with 0.08 % T.H.D.)110 W + 110 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.)Center: 80 W (8 Ω/ohms, 20 Hz ~ 20 kHz with 0.08 % T.H.D.)110 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.)Surround: 80 W + 80 W (8 Ω/ohms, 20 Hz ~ 20 kHz with 0.08 % T.H.D.)110 W + 110 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.)Surround Back:80 W (8 Ω/ohms, 20 Hz ~ 20 kHz with 0.08 % T.H.D.)110 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.)Dynamic power: 100 W x 2 ch (8 Ω/ohms)145 W x 2 ch (4 Ω/ohms)170 W x 2 ch (2 Ω/ohms)Output terminals: Front/Center/Surround: 16 to 16 Ω/ohmsSurround Back: A or B 16 to 16 Ω/ohmsA + B 12 to 16 Ω/ohms• AnalogLINE input - PRE OUTInput sensitivity/input impedance: 200 mV/47 kΩ/kohmsFrequency response: 10 Hz ~ 100 kHz: +1, –3 dB (DIRECT mode)S/N ratio: 100 dB (IHF-A weighted) (DIRECT mode)Distortion: 0.008% (20 Hz ~ 20 kHz) (DIRECT mode)Rated output: 1.2 V• Phono equalizer (PHONO input — REC OUT)Input sensitivity: 2.5 mVRIAA deviation: ±1 dB (20 Hz to 20 kHz)Signal-to-noise ratio: 74 dB (A weighting, with 5 mV input)Rated output / Maximum output: 150 mV / 7 VDistortion factor: 0.03% (1 kHz, 3 V)20 SPECIFICATIONS2 Video section• Standard video jacksInput/output level and impedance: 1 V p-p, 75 Ω/ohmsFrequency response: 5 Hz ~ 10 MHz — +1, –3 dB• S-video jacksInput/output level and impedance: Y (brightness) signal — 1 Vp-p, 75 Ω/ohmsC (color) signal — 0.286 Vp-p, 75 Ω/ohmsFrequency response: 5 Hz ~ 10 MHz — +1, –3 dB• Color component video terminalInput / output level and impedance: Y (brightness) signal — 1 Vp-p, 75 Ω/ohmsPB /C B (blue) signal — 0.7 Vp-p, 75 Ω/ohmsPR /C R (red) signal — 0.7Vp-p, 75 Ω/ohmsFrequency response: 5 Hz ~ 27 MHz — +1, –3 dB2 Tuner section[FM] (note: μ V at 75 Ω/ohms, 0 dBf = 1 x 10–15 W) [AM]Receiving range: 87.50 MHz ~ 108.00 MHz 522 kHz ~ 1611 kHzUsable sensitivity: 1.0 μV (11.2 dBf) 18 μV50 dB quieting sensitivity: MONO 1.6 μV (15.3 dBf)STEREO 23 μV (38.5 dBf)S/N ratio: MONO 80 dB (IHF-A weighted)STEREO 75 dB (IHF-A weighted)Total harmonic distortion: MONO 0.15 % (1 kHz)STEREO 0.3 % (1 kHz)2 GeneralPower supply: AC 230 V, 50 HzPower consumption: 260 W1 W Max. (Standby)Maximum external dimensions: 434 (W) x 171 (H) x 417 (D) mmMass: 11.7 kg2 Remote control unit (RC-917)Batteries: R6P/AA Type (two batteries)External dimensions: 55 (W) x 225 (H) x 34.5 (D) mmMass: 165 g (including batteries)For purposes of improvement, specifications and design are subject to change without notice.