Denon DN-X300 Operating Instructions Manual

Also see for DN-X300: Operating instructions Service manual Service manual

Contents

6ENGLISH!7 Input select switch• Switches between the PHONO/LINE and LINEinputs.• When the lever of switch is vertical position, theLINE2 or LINE4 input is selected.• When the lever of switch is slope, thePHONO1/LINE1 or PHONO2/lINE3 input isselected.• You can perform 8 direction placement. Seepage 10.!8 SPLIT CUE button• In the STEREO mode, the stereo sound ofMASTER and CUE are fed to both ear cups. Inthe SPLIT CUE mode, the headphone circuitprovides monaural CUE sound to the left andmonaural MASTER sound to the right.• When the Level Meter mode select switch isset to “MASTER”…In the STEREO mode, themeter indicates the stereo level in the L/RMaster output. In the SPLIT CUE mode, themonaural CUE sound level is displayed on theleft and the monaural MASTER sound level isdisplayed on the right.• In the SPLIT CUE mode, the LED is lit.!9 PGM 1/2 KILLS switches• These switches are used cut out the Treble, Midor Bass frequencies of the incoming audiosignal. When these switches moved up ordown, the selected frequency level is cut, theLED located directly above the specific switchwill glow indicating the cut function has beenactivated.@0 Level meter mode select switch• The position of this switch will determine theLevel Meter mode. In the “MASTER” position,the meter will detail the out level of the left andright channels. In the “PGM 1/2” position, theleft side of the meter will indicate monaurallevel of the PGM 1 and the right side of themeter will indicate monaural level of the PGM 2.@1 Channel Fader• Controls the channel output level.@2 Level meter• The dual LED's indicators are used to detaileither the master output level, a combination ofthe master output level and the CUE signallevel, or the PGM1/2 monaural level.@3 Crossfader• Fades the overall mixer output betweenchannels 1 and 2.(2) Rear panel@4 Power operation switch (POWER)• Selects power “ON” or “OFF”.NOTE:Whenever the power switch is in the OFF state,the AC adaptor is still connected on AC linevoltage. Please be sure to unplug the cord whenyou don’t use for along time.@5 BALANCED MASTER OUT jacks• These 1/4” TRS jacks provide a balanced linelevel output.• Connect these jacks to the balanced analoginput jacks on an amplifier or console.• Pin layout: Tip=Hot Ring=Cold Sleeve=GND@6 EFFECT LOOP SEND/RETURN jacks• These 1/4” TS stereo jacks allow externalprocessing of the program signal.• When connect monaural type effect processor,use Lch input and output.@7 MIC BALANCED INPUT jack• Accepts an balanced microphone with 1/4” TRSmono jacks.• Pin layout: Tip=Hot Ring=Cold Sleeve=GND@8 MIC EFFECT LOOP jack• These 1/4” TRS jack allow external processingof the program signal.• Pin layout:Tip=SEND Ring=RETURN Sleeve=GND@9 PGM1, 2 FADER output jacks• Connect these jacks to the FADER input jacks ofDN-S3000, DN-S5000, DN-S1000 and etc. usingthe 3.5mm stereo mini cord.#0 Phono ground screw (GND)• This screws provide a place to connect theground wire from a turntable.• This terminal is exclusively for a turntableground and not a safety earth ground.#1 PHONO1, 2 / LINE1, 3 switches(LN / PH)• These switches change the input from PHONOto a LINE level input.• These switches set a LINE level input whenturntable is not connected.NOTE:Always be sure main power is shut off beforechange the position of the Line Level SelectorSwitch.#2 PHONO1, 2 / LINE1, 3 input jacks• These stereo pairs of unbalanced RCA jacks areinputs for a PHONO (RIAA) stage for magnetic(MM) cartridges or a LINE stage suitable for anydevice, such as a CD player.#3 LINE2, 4 input jacks• These stereo pairs of unbalanced RCA jacks areinputs for any line level device.#4 AUX INPUT jacks• This stereo pair of RCA jacks provides anunbalanced line level input with independent toppanel AUX INPUT control.• This input is mixed after the Crossfader andEFFECT LOOP.#5 BOOTH OUT jacks• This stereo pair of RCA jacks is the same as theMASTER output with independent BOOTHLEVEL control.• This output may be for recording, booth/zonemonitoring, or for connecting to another mixer.#6 UNBALANCED MASTER OUT jacks• This stereo pair of RCA jacks provides anunbalanced line level output.• Connect these jacks to the unbalanced analoginput jacks on an amplifier or console.#7 AC IN• Input connection for the included AC adaptor.NOTE:Use specified attached AC adaptor only.(3) Front panel#8 CH 1/2 FADER START switches• Use this to switch the Channel Fader Startfunction ON and OFF.#9 CROSSFADER START A, B switches• Use this to switch the Crossader Start functionON and OFF.$0 HEADPHONE output jack• Accept 1/4” stereo headphone plugs.$1 CH 1/2 FADER CONTOURadjustment• Adjusts the curve of the CH1/2 faders betweenfast, normal , or slow fade.$2 CH 1/2 FADER REVERSE switch• Reverses the direction of each respective inputCH1/2 fader.$3 CROSSFADER CONTOURadjustment• Adjusts the shape of the crossfader curve froma fast cut for scratching or to a slow fade formixing.$4 CROSSFADER REVERSE switch• Reverses the direction of the crossfader.