23System OperationsUsing the optimised filterThe filter optimised for the properties of the SC-F102/F103 (soldseparately) can be used.NOTE:• The editing function does not work with discs containing 26tracks or more.• When using the edited recording function, be sure to load thecassette tape with side A facing upwards. The beginning of thecassette tape is found automatically before recording starts.• When using a tape that is already recorded on, erase the tapebefore conducting edited recording.• When using the edited recording function, set the cassettedeck’s reverse mode to “ ”.• In some cases it may not be possible to record all the tracks onthe cassette tape even if its length is longer than the total lengthof the tracks on the disc, due to the fact that the tracks must bedivided between sides A and B. “OVER” is displayed on theDCD-F102’s display if there are tracks that cannot be recorded. If“OVER” is displayed, change the length of the cassette tape asdescribed in step 3.• When the editing function is in use, no buttons other than, MENU/SET, [9], CD 1/3, CD 2, 2>, and[TIME/DISPLAY] will operate.• With edited recording, blank sections approximately 4 secondslong are automatically created between tracks. If you do not wantthese blank sections, do not use edited recording.• Edited recording is not possible with discs containing files in MP3or WMA format.PageMeasuresCauseSymptomIf a problem should arise, first check the following.1. Are the connections correct?2. Have you operated the player according to the Operating Instructions?If this unit is not operating properly, check the items listed in the table below. Should the problem persist, there may be a malfunction.Disconnect the power immediately and contact your store of purchase.Display does not light and no soundis produced when power is turnedon.• The power supply cord is not plugged into a poweroutlet.• Plug the power supply cord into a power outlet. 7OthersDisplay lights but no sound isproduced.• The speaker cables are not properly connected.• The input is not properly selected.• The volume is set too low.• Connect securely.• Connect in the proper position.• Adjust the volume to an appropriate level.8711No sound is produced from onceside.• The speaker cables are not properly connected.• The input cables are not properly connected.• The left/right balance is off.• Connect securely.• Connect securely.• Adjust the left/right balance.8711For stereo sources, the positions ofthe instruments are inverted.• The connections of the speaker cables or input cablesare inverted.• Check the connections. 7Buzzing noise in FM broadcasts. • The antenna cable is not properly connected.• Noise is entering from an electronic device equippedwith a microprocessor, or the signal from thebroadcast system is weak.• Connect the antenna properly.• Change the layout of the equipment or the positionsor directions of the connection cables, antenna, etc.• Connect an outdoor antenna.999Hissing or buzzing noise is heard inAM broadcasts.• Noise is entering from a monitor, etc., or there isinterference.• Turn off the monitor.• Change the position or direction of the AM loopantenna.• Connect an outdoor antenna.—99Humming noise is heard in AMbroadcasts.• There is interference from signals conveyed throughthe power supply cord.• Connect an outdoor antenna. 9System operations do not work. • The system cables are not properly connected. • Connect securely. 7When playing records, a wailingnoise is produced when the volumeis raised.• The player and speakers are too close together.• The floor is soft and vibrates easily.• Move the player and speakers as far apart as possible.• Use cushions to absorb the vibrations of the speakersbeing conveyed from the floor.10—Remote control unit does notoperate.• The batteries are flat.• The remote control unit is too far away.• There is an obstacle between the main unit and theremote control unit.• The remote control unit is being operated at an angleof over 30° with respect to the front panel.• The batteries are inserted in the wrong direction.• Replace with new batteries.• Operate from closer to the main unit.• Remove the obstacle.• Operate the remote control unit from directly in frontof the main unit.• Insert the batteries in the proper direction.22222TroubleshootingUse [88] or [99] to set.2Press MENU/SET.31 Use MENU/SET to select “SPK OPTIMISE”.ON:This sets the optimum properties for the SC-F102/F103 (soldseparately).OFF:When this is set, the response is flat.
