Denon DVD-3930 Operating Instructions Manual

Also see for DVD-3930: Specification Service manual Service manual

HDMI audio settingDevice to be connectedConnections ConnectionsENGLISH11ENGLISHDENON LINK connectionsDENONLINKEWhen connected to a DENON LINK-compatible AV amplifier, the multi-channel signals of DVD-Audiodiscs, Super Audio CDs, etc., can be transferred as such in digital format.Connection to a device with an HDMI terminalHDMIINJConnecting the DVD-3930 to device with an HDMI terminal using an HDMI cable (sold separately) enablesdigital transfer of both digital video signals and multi-channel audio signals.HDMI audioAudio recording formatDisc type¢ Audio setting of device to be connected with an HDMI terminal ( page 17)2CHMULTI(LPCM)MULTI(NORMAL)The multi-channel audio signals are output from the analogaudio output and DENON LINK terminal.Down-mixed 2-channel audio signals are output from the HDMIoutput terminal.The DTS or Dolby Digital signals can be decoded by theconnected TV or AV amplifier.(The HDMI audio speaker setting, etc., cannot be made.)Multi-channel audio signals are output from the HDMI terminal.The HDMI audio speaker setting, etc., can be made.Device compatible with DTS orDolby Digital decodingDevice compatible with 3 ormore channels of audio inputs(not DTS or Dolby Digitalcompatible)Device compatible with 2-channel audio input or devicenot compatible with audioinputDVD-AudioDolby DigitalDTSPCMLPCM or PPCMVideo CDMusic CDMP3 CD2-channel PCM Multi PCM2CH MULTI (NORMAL) MULTI (LPCM)2-channel PCM Multi PCMDVD-VideoDolby DigitalDTS2-channel PCMWMA CDSuper audio CDMulti PCMMulti PCMMulti PCMMPEG Audio 2-channel PCM Multi PCM Multi PCM2-channel PCM 2-channel PCM 2-channel PCM2-channel PCM 2-channel PCM 2-channel PCM2-channel PCM 2-channel PCM 2-channel PCM2-channel PCM 2-channel PCM 2-channel PCMNo output No output No outputNo output No output No output2-channel PCM 2-channel PCM 2-channel PCMMulti PCM2-channel PCMStereo areaMulti areaCD layer¢ For a TV, amplifier, etc.Status of signal fromthe DVD-3930’s HDMIoutput terminalDVI-D-compatible monitor(Not HDCP compatible)DVI-D-compatible monitor(HDCP compatible)HDMI-compatible monitor¢ Connection with an HDMI/DVI-D conversion cable (adapter)• HDMI video streams (video signals) are compatible with DVI-D.The DVD-3930 can be connected to a TV with a DVI-D terminal using an HDMI/DVI-D conversion cable(adapter), but depending on the combination of devices in some cases no picture will be output.• When using an HDMI/DVI-D conversion adapter, the picture may not be output properly due to poorcontact with the connected cable.Only video signals output * Neither video nor audiosignals outputBoth video and audiosignals output* The video signals are only output in RGB format.• Digital transfer is possible up to 24 bit/2ch for 192/176.4 kHz, 24 bit/6ch for 96 kHz or less.• When making DENON LINK connections, be sure to check the version of the AV amplifier to beconnected then make the “DENON LINK” setting at “initial settings” appropriately ( page 19). If twoDENON LINK terminals of different versions are interconnected, there may be no sound or only noise.• When “DENON LINK” is set, downmixed audio signals are output from the DVD-3930’s analog audiooutput terminals (L/R, FL/FR and AV-1). When using the 5.1-channel analog audio terminals, set the“DENON LINK” setting in the initial settings to “OFF”.• The DVD-3930’s speaker settings are invalidated when the DENON LINK terminal is connected. (Makethe speaker settings on the AV amplifier to which the DVD-3930 is connected.)• With the DENON LINK 2nd connection, Super Audio CD’s multi and stereo signals are not output fromthe DENON LINK terminal. Please use the analog audio output terminals.Monitor orAV amplifierAV amplifier