Denon DVD-5900 Service Manual

Also see for DVD-A11: Operating instructions Operating instructions

Contents

Denon DVD-5900 Service Manual Manual pdf 54 page image

5454DVD-5900/DVD-A1150 TESTO O Output for TEST. (open)51 TESTI I Input for TEST. It fixed to “L” potential.52 TESTI I Input for TEST. It fixed to “L” potential.53 TESTO O Output for TEST. (open)54 VDC - +2.5V Power for CORE.55 DSADML O DSD Data output terminal for Lch Down Mix.56 DSADMR O DSD Data output terminal for Rch Down Mix.57 BCKASL I I/O selection terminal of the Bit clock for DSD data output. L=input (Slave), H=output (Master)58 VSDSD - Ground terminal for DSD data output.59 BCKAI I Bit clock input terminal for DSD data output.Input a Bit clock into this terminal at the time of BCKASL=”L” potential.60 BCKAO O Bit clock output terminal for DSD data output.Bit clock output from this terminal at the time of BCKASL=”H” potential.61 PHREFI I Reference phase signal input terminal for DSD output phase modulation.62 PHREFO O Reference phase signal output terminal for DSD output phase modulation.63 ZDFL O Lch zero-data detection flag (at the time of μcom setup).It will be set to “H” if non-sound data continues 300 msecs.64 DSAL O DSD data output terminal for Lch speaker.65 ZDFR O Rch zero-data detection flag (at the time of μcom setup).It will be set to “H” if non-sound data continues 300 msecs.66 DSAR O DSD data output terminal for Rch speaker.67 V DDSD - +3.3V Power for DSD data output.68 ZDFC O Cch zero-data detection flag (at the time of μcom setup).It will be set to “H” if non-sound data continues 300 msecs.69 DSAC O DSD data output terminal for Cch speaker.70 ZDFLFE O LFEch zero-data detection flag (at the time of μcom setup).It will be set to “H” if non-sound data continues 300 msecs.71 DSASW O DSD data output terminal for SWch speaker.72 VSDSD - Ground for DSD data output.73 ZDFLS O LSch zero-data detection flag (at the time of μcom setup).It will be set to “H” if non-sound data continues 300 msecs.74 DSALS O DSD data output terminal for LSch speaker.75 ZDFRS O RSch zero-data detection flag (at the time of μcom setup).It will be set to “H” if non-sound data continues 300 msecs.76 DSARS O DSD data output terminal for RSch speaker.77 V DDSD O +3.3V Power for DSD data output.78 IOUT0 O Data output terminal 0 for IEEE1394 link chip I/F.79 IOUT1 O Data output terminal 1 for IEEE1394 link chip I/F.80 VSC - Ground for CORE.81 IOUT2 O Data output terminal 2 for IEEE1394 link chip I/F.82 IOUT3 O Data output terminal 3 for IEEE1394 link chip I/F.83 VDC - +2.5V Power for CORE.84 IOUT4 O Data output terminal 4 for IEEE1394 link chip I/F.85 IOUT5 O Data output terminal 5 for IEEE1394 link chip I/F.86 VSIO - Ground for I/O.87 IANCO O Transmission information data output terminal for IEEE1394 link chip I/F.88 IFULL I Data transmission hold request signal input terminal for IEEE1394 link chip I/F.89 IEMPTY I High speed transmission request signal input terminal for IEEE1394 link chip I/F.90 VDIO - +3.3V Power for I/O.91 IFRM O Frame reference signal output terminal for IEEE1394 link chip I/F.92 IOUTE O Enable signal output terminal for IEEE1394 link chip I/F.93 IBCK O Data transmission clock output terminal for IEEE1394 link chip I/F.94 VSC - Ground for CORE.95 TESTI I TEST input terminal. It fixed to “H” potential.Pin Name I/O Functionswww. xiaoyu163. comQQ 376315150 992894298TEL 13942296513 992894298051513673QQTEL 13942296513 QQ 376315150 892498299TEL 13942296513 QQ 376315150 892498299http://www.xiaoyu163.comhttp://www.xiaoyu163.com