Desa LMFP33NR Owner's Operation And Installation Manual

Also see for LMFP33NR: OWNER'S OPERATION AND INSTALLATION MANUAL OWNER'S OPERATION AND INSTALLATION MANUAL OWNER'S OPERATION AND INSTALLATION MANUAL OWNER'S OPERATION AND INSTALLATION MANUAL OWNER'S OPERATION AND INSTALLATION MANUAL

Desa LMFP33NR Owner's Operation And Installation Manual Manual pdf 18 page image

111604-01AFor more information, visit www.desatech.comFor more information, visit www.desatech.com18AUTO MANOPERATING FIREPLACELighting Instructions (Cont.)To Turn Off Gas To ApplianceManual Lighting Procedure1. STOP! Read the safety information, page 17 column 2.2. Make sure equipment shutoff valve is fully open.3. Set remote selector switch in the AUTO position (see Figure 34).4. Press in and turn control knob clockwise to theOFF position (see Figure 34).5. Wait five (5) minutes to clear out any gas. Then smell forgas, including near the floor. If you smell gas, STOP! Fol-low “B” in the safety information, page 17 column 2. If youdon’t smell gas, go to the next step.6. Press in and turn control knob counterclockwiseto the PILOT position. Press in control knob for five (5)seconds (see Figure 34).Note: You may be running this heater for the first timeafter hooking up to gas supply. If so, the control knob mayneed to be pressed in for 30 seconds or more. This will al-low air to bleed from the gas system.7. With control knob pressed in, press and release ignitor but-ton. This will light pilot. The pilot is attached to the rear ofthe front burner. If needed, keep pressing ignitor button untilpilot lights.Note: If pilot does not stay lit, contact a qualified serviceperson or gas supplier for repairs. Until repairs are made,light pilot with match. To light pilot with match, see ManualLighting Procedure.WARNING: Damper handle will be hot if heaterhas been running.WARNING: Burners will come on automaticallywithin one minute when the control valve is in the ONposition after the pilot is lit.Control KnobIgnitor ButtonFigure 34 - Remote Selector Switch, Control Knob and IgnitorButtonRemote Selector SwitchOPERATING HEATERContinuedNote: Home owners generally prefer to operate their heaterwith the chimney damper closed. This will put all the heat intothe room. However, there may be times you will desire the fullflames of the highest heat setting but will find the heat outputexcessive. You can open the chimney damper (if you have one)fully or partially to release some of the heat.Shutting Off HeaterPress on/off key on remote control and turn control knobclockwise to the OFF position (see Figure 34).Shutting Off Burners Only (pilot stays lit)Press the on/off key on remote control or turn control knobclockwise to the PILOT position.TO TURN OFF GASTO APPLIANCEMANUAL LIGHTINGPROCEDURE1. Follow steps 1 through 7 under Lighting Instructions,column 1.2. Depress control knob and light pilot with match.3. Keep control knob pressed in for 30 seconds after lightingpilot. After 30 seconds, release control knob. Now follow steps9 through 11 under Lighting Instructions above.CAUTION: Do not try to adjust heating levels byusing the equipment shutoff valve.Figure 35 - Pilot (Propane/LP)IgnitorElectrodePilot BurnerFigure 36 - Pilot (Natural)IgnitorElectrodePilot Burner8. Keep control knob pressed in for 30 seconds after lightingpilot. After 30 seconds, release control knob.• If control knob does not pop out when released, contacta qualified service person or gas supplier for repairs.Note: If pilot goes out, repeat steps 4 through 8.9. Slightly push in and turn control knob counterclockwiseto the ON position.10. Press the on/off key on the remote control to turn on appli-ance main burner. Wait at least 5 seconds before settingdesired flame height.11. Press the up or down key until the small triangle is to theleft of large flame icon at the top of LCD display (see Fig-ure 37, page 19). Press the left or right key to set the de-sired flame height.