Desa (V) CB36(N Owner's Operation And Installation Manual

16www.desatech.com117437-01OPERATING FIREPLACE - Manual Ignition SystemFor Your Safety Read Before LightingLighting InstructionsTo Turn Off Gas To ApplianceManual Lighting Procedure• If you cannot reach your gas supplier, call the fire department.C. Use only your hand to push in or turn the gas controlknob. Never use tools. If the knob will not push in orturn by hand, don’t try to repair it, call a qualifiedservice technician. Force or attempted repair mayresult in a fire or explosion.D. Do not use this appliance if any part has been underwater. Immediately call a qualified service techni-cian to inspect the appliance and to replace any partof the control system and any gas control which hasbeen under water.LIGHTINGINSTRUCTIONS1. STOP! Read the safety information above.2. Open lower louver panel.3. Turn off all electric power to the fireplace.4. Push in gas control knob slightly and turn clockwiseto “OFF” (see Figure 33).5. Wait five (5) minutes to clear out any gas. Then smell for.gas, including near the floor. If you smell gas, STOP! Fol-low “B” in the safety information above. If you don’t smellgas go to the next step.6. The pilot is located by the main burner and should not re-quire accessing for lighting.7. Turn gas control knob counterclockwise to “PILOT”.8. Push in gas control knob all the way and hold. Immedi-ately light the pilot by repeatedly depressing the piezo sparkignitor until a flame appears. Continue to hold for aboutone (1) minute after the pilot is lit. Release gas control knoband it will pop back. Pilot should remain lit. If it goes out,repeat steps 5 through 8.Figure 33 - Control Valve MillivoltTO TURN OFF GASTO APPLIANCE1. Open lower louver panel.2. Set the wall switch to the OFF position or the GHRC selectorswitch (when equipped) to prevent draining the battery.3. Turn off all electric power to the appliance if service is tobe performed.4. Push in gas control knob slightly and turn clockwiseto “OFF”.5. Close lower louver panel.Shutting Off Berners Only (pilot stays lit)You may shut off the burners and keep the pilot lit by doing oneof the following:1. Turn gas control knob clockwise to the PILOT position.2. Set the wall switch to the OFF position or the HRC selectorswitch (when equipped) to prevent draining the battery.MANUAL LIGHTINGPROCEDURE1. Remove glass door (see Removing/Replaceing Glass Door,page 14).2. Follow steps 1 through 8 under Lighting Instructions.3. Depress gas control knob and light pilot with match.4. Keep gas control knob pressed in for 30 seconds after light-ing pilot. After 30 seconds, release gas control knob. Fol-low steps 10 through 11 under Lighting Instructions.5. Replace glass door (see Removing/Replacing Glass Door,page 14).OFFPILOTONPiezoIgnitorGas ControlKnobRegulator CapOPERATING FIREPLACEManual Ignition SystemFOR YOUR SAFETY READBEFORE LIGHTINGWARNING: If you do not follow these instructionsexactly, a fire or explosion may result causing prop-erty, damage, personal injury or loss of life.A. This appliance has a pilot which must be lighted by hand.When lighting the pilot, follow these instructions exactly.B. BEFORE LIGHTING smell all around the appliance areafor gas. Be sure to smell next to the floorbecause some gasis heavier than air and will settle on the floor.WHAT TO DO IF YOU SMELL GAS• Do not try to light any appliance.• Do not touch any electric switch; do not use any phonein your building.• Immediately call your gas supplier from a neighbor’sPhone. Follow the gas supplier’s instructions.• If gas control knob does not pop up when released, stopand immediately call your service technician or gas suppier.• If the pilot will not stay lit after several tries, turn thegas control knob to “OFF” and call your service techni-cian or gas supplier.9. Turn on all electric power to fireplace.10. Turn gas control knob counterclockwise to “ON”.11. Close lower louver panel.