I.B. 32-255-1G Page 1Effective 12/02SECTION 1: INTRODUCTION1-1 PRELIMINARY COMMENTS AND SAFETY PRE-CAUTIONSThis technical document is intended to cover mostaspects associated with the installation, operation andmaintenance of Type VCP-W, VCPW-SE, and VCPW-ND Vacuum Circuit Breakers. It is provided as a guidefor authorized and qualified personnel only. Please referto the specific WARNING and CAUTION in Paragraph1-1.2 before proceeding past Section 1. If further infor-mation is required by the purchaser regarding a particu-lar installation, application or maintenance activity, aCutler-Hammer representative should be contacted.1-1.1 WARRANTY AND LIABILITY INFORMATIONNO WARRANTIES, EXPRESSED OR IMPLIED,INCLUDING WARRANTIES OF FITNESS FOR A PAR-TICULAR PURPOSE OF MERCHANTABILITY, ORWARRANTIES ARISING FROM COURSE OF DEAL-ING OR USAGE OF TRADE, ARE MADE REGARDINGTHE INFORMATION, RECOMMENDATIONS ANDDESCRIPTIONS CONTAINED HEREIN. In no event willCutler-Hammer be responsible to the purchaser or userin contract, in tort (including negligence), strict liability orotherwise for any special, indirect, incidental or conse-quential damage or loss whatsoever, including but notlimited to damage or loss of use of equipment, plant orpower system, cost of capital, loss of power, additionalexpenses in the use of existing power facilities, orclaims against the purchaser or user by its customersresulting from the use of the information and descrip-tions contained herein.1-1.2 SAFETY PRECAUTIONSAll safety codes, safety standards and/or regulationsmust be strictly observed in the installation, operationand maintenance of this device.THE WARNINGS AND CAUTIONS INCLUDED ASPART OF THE PROCEDURAL STEPS IN THIS DOCU-MENT ARE FOR PERSONNEL SAFETY AND PRO-TECTION OF EQUIPMENT FROM DAMAGE. ANEXAMPLE OF A TYPICAL WARNING LABEL HEAD-ING IS SHOWN ABOVE IN REVERSE TYPE TOFAMILIARIZE PERSONNEL WITH THE STYLE OFPRESENTATION. THIS WILL HELP TO INSURETHAT PERSONNEL ARE ALERT TO WARNINGS,WHICH MAY APPEAR THROUGHOUT THE DOCU-MENT. IN ADDITION, CAUTIONS ARE ALL UPPERCASE AND BOLDFACE AS SHOWN BELOW.COMPLETELY READ AND UNDERSTAND THEMATERIAL PRESENTED IN THIS DOCUMENTBEFORE ATTEMPTING INSTALLATION, OPERATIONOR APPLICATION OF THE EQUIPMENT. IN ADDI-TION, ONLY QUALIFIED PERSONS SHOULD BEPERMITTED TO PERFORM ANY WORK ASSOCIAT-ED WITH THE EQUIPMENT. ANY WIRING INSTRUC-TIONS PRESENTED IN THIS DOCUMENT MUST BEFOLLOWED PRECISELY. FAILURE TO DO SOCOULD CAUSE PERMANENT EQUIPMENT DAMAGE.1-2 GENERAL INFORMATIONThe purpose of this book is to provide instructions forunpacking, storage, use, operation and maintenance ofType VCP-W, VCPW-SE, and VCPW-ND Vacuum CircuitBreakers. These circuit breakers are horizontal drawouttype removable interrupting elements designed for usein VacClad-W Metal-Clad Switchgear and appropriateVCP-W modules. They provide reliable control and pro-tection for medium voltage electrical equipment and cir-cuits. All VCP-W circuit breaker elements are designedto ANSI Standards for reliable performance, ease ofhandling and simplified maintenance. In addition, VCP-W circuit breakers are tested to both ANSI and IECStandards for application around the world.The VCPW-SE circuit breaker element is a VCP-W cir-cuit breaker designed specifically for special environ-ment applications and operating conditions through 27kV. The VCPW-ND circuit breaker element is a narrowdesign VCP-W circuit breaker designed specifically foruse in 5 kV applications where floor space requirementswould not allow the industry standard 36 inch wideswitchgear. From this point on, all circuit breaker ele-ments will be referred to as Type VCP-W unless the ref-erence is specific to a particular design.SATISFACTORY PERFORMANCE OF THESE CIRCUITBREAKER ELEMENTS IS CONTINGENT UPON PROP-ER APPLICATION, CORRECT INSTALLATION ANDADEQUATE MAINTENANCE. THIS INSTRUCTION! CAUTION! WARNING! WARNING