Eaton ALL-PRO MS185DW Instruction Manual

Questions?/Des questions?/¿Preguntas? 1-800-334-6871 ConsumerProducts@eaton.com1PACKAGING CONTENTS/ C O N T E N U DE L ’ E MBALLAGE/ C O N T E N I DO DEL P A Q U E T EInstruction Manual/InstruccionesCAUTION• Connect fixture to a 120 volt, 60 Hz power source. Any other connection voidsthe warranty.• Fixture must be mounted to a grounded recessed junction box marked for usein wet locations.• Suitable for wall mount or eave mount only. NOT suitable for ground mount installation.• Fixture should be installed by persons with experience in household wiring or by aqualified electrician. The electrical system, and the method of electrically connectingthe fixture to it, must be in accordance with the National Electrical Code and localbuilding codes.• Do not allow sensor head to touch light housing – maintain at least 1 in. spacebetween fixture and sensor.• Keep away from flammable objects. Do not position fixture within2 in. of any combustible materials.• MINIMUM 90°C SUPPLY CONDUCTORS.• For proper operation and protection against damage, the motionsensor head adjustment knobs must be facing the ground.• Do not use this apparatus near water.• Clean only with a dry cloth.• Do not block any ventilation openings. Install in accordance with the manufacturer’sinstructions.• Do not install near any heat sources such as radiators, heat registers, stoves or otherapparatus (including amplifiers) that produce heat.• Only use attachments/accessories specified by the manufacturer.• This device complies with Part 15 of the FCC Rules. Operation is subject to thefollowing two conditions: (1) This device may not cause harmful interference, and(2) this device must accept any interference received, including interference thatmay cause undesired operation. Under Part 15 of the FCC Rules, any changes ormodifications to the motion detector described in this instruction sheet that arenot expressly approved by Eaton could void the user’s authority to operatethe equipment.NOTE: This equipment has been tested and found to comply with the limits fora Class B digital device, pursuant to Part 15 of the FCC Rules. These limits aredesigned to provide reasonable protection against harmful interference in aresidential installation. This equipment generates, uses and can radiate radiofrequency energy and if not installed and used in accordance with the instructions,may cause harmful interference to radio communications. However, there is noguarantee that interference will not occur in a particular installation. If this equipmentdoes cause harmful interference to radio or television reception, which can bedetermined by turning the equipment off and on, the user is encouraged to try tocorrect the interference by one or more of the following measures:- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver.- Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected.- Consult the dealer or an experienced radio/TV technician for help.ITEMS REQUIRED(Purchase separately)• Phillips screwdriver• Outdoor weatherproof silicone caulking• (2) 100 watt (MAX) PAR 38 floodlight bulbsNOTE: This fixture was designed to work with up to 150 watt maximum PAR halogen floodbulbs. For improved energy efficiency, lower wattage PAR halogen flood bulbs may be used.Compact Fluorescent (CFL) bulbs contain electronics which may interfere with the motionsensing function of your fixture and are not recommended. To meet ENERGY STAR ®requirements, maximum total lamp wattage can not exceed 250 watts.HOW IT WORKSPIR does a good job of detecting lateral motion across the 180°range of detection. Precision Plus Doppler Radar™ does anexcellent job detecting motion towards and away from the unit.Both systems combined provide enhanced accuracy and completecoverage within the detection range. Motion from any direction willtrigger your floodlight—even during hot or cold temperature extremes.IMPORTANT SAFETY INSTRUCTIONSWhen using product, basic precautions should always be followed, including the following:• Heed all warnings, including below warnings AND those included on product.• Save these instructions and warnings.• For outdoor use only.• cETLus LISTED for wet location.• Disassembling your fixture will void the warranty.• Your fixture is prewired and preassembled for easy installation.• Read and follow these instructions.• To reduce the risk of a burn during relamping, disconnect power supply to the unitbefore relamping.• Bulb gets HOT quickly!• The bulb and fixture get extremely hot during use. Disconnect power and allow fixtureto cool before changing bulb or handling fixture.• Always replace bulb with the same wattage or lower wattage than marked. Installinga bulb of a higher wattage could create a fire hazard. Use of a higher wattage bulb willvoid the warranty. (Maximum 150 watt PAR halogen bulb.) .MS185D (Bronze)ENGLISHUp to70 feet180 degreesB. (2) Lampholder gaskets(2) Juntas obturadorasdel receptáculo(2) Joints statiques de douilleWARNINGA. Motion detectorand light fixtureDetector de movimientoy accesorioLuminaire avec détecteurde mouvementD. (3) Wire nuts(3) Conectores del cables(3) Capuchons de connexionC. (2) #6 and (2) #8 mounting screws(use the size that fits your junction box)(2) Tornillos #6 y (2) tornillos #8 de montaje (utilice eltamaño que mejor se adecue a su caja de conexión)(2) vis nº 6 et (2 )vis nº 8 pour boîte de jonction (choisissezla dimension convenant à votre boîte de jonction)MS185DW (White)