Eaton ALL-PRO MSS1301LW Instruction Manual

1Questions?/Des questions?/¿Preguntas? 1-800-334-6871 ConsumerProducts@eaton.comInstruction Manual/Manuel d’instructions/Instrucciones• Locate sensor away from moving objects such as trees, large shrubs and street traffic.• You will need to adjust the angle of the solar panel throughout the year as seasons changein order to keep it at the best possible angle to the sun.• Keep solar panel clear of any objects that will block the sunlight. It will be necessary toperiodically clean the solar panel with soft wet cloth.• During periods of several cloudy days, the battery may fall below the operating level andwill need to be recharged with sunlight.MOUNTING YOUR FIXTURE1. Locate area in which you would like to install yourlight fixture.NOTE: For fixture to operate properly, the solar panel (B)must be located in an area that will receive the maximumamount of sunlight and is free from obstructions.2. Using the fixture mounting screws (C) provided,mount the snap-in mounting bracket (E) to a solidsurface 6-8 feet above the ground by placing thescrews through the center holes of the bracket.Make sure the arrow on the bracket is pointing up.(Fig. 2).3. Slide fixture down over the snap-in mountingbracket, making sure that the fixture engages theguide ribs. Continue sliding down until the fixturesnaps into the locking tab.4. Using the solar panel mounting screws (D) provided,mount solar panel (B) to a solid surface (Fig. 3).Adjust the angle of the solar panel (B) so that it willreceive the maximum amount of direct sunlightduring the daylight hours.NOTE: For best results, locate panel to receive at least3-4 hours of direct sunlight daily.5. Carefully route the wire from the solar panel (B)to the fixture (A) and plug it into the connectorextending from the side of the fixture housing (A)(Fig. 4). Make sure to push the connector plugstightly together until you hear two clicks to ensurethey are fully engaged.PACKAGING CONTENTS/CONTENIDO DEL PAQUETEITEMS REQUIRED(Purchase separately)• Phillips screwdriverHOW IT WORKSDuring the daylight hours, the solar panel turns the sunlightinto energy that is stored in the rechargeable battery pack.Your light features a motion sensor that turns the light ONat night when motion is detected. This light is equippedwith a photocell, which only allows the fixture to turn ONduring the nighttime hours.WARNINGS AND CAUTIONSINSTRUCTIONS PERTAINING TO A RISK OF FIRE OR INJURY TO PERSONS.To reduce the risk of fire or injury to persons, read and follow these instructions:• DO NOT replace batteries.• DO NOT dispose of this product in fire. Batteries inside this product may explode or leak.• DO NOT puncture this battery pack. DO NOT work on this battery pack• DO NOT disassemble fixture. The fixture does not have any user serviceable parts.• For outdoor use only.• Lithium-Ion batteries must be disposed of in accordance with local waste ordinances andregulations.• Do not operate luminaire with a missing or damaged lens.• Fixture is suitable for wall mount only. NOT suitable for ground mount installation.• Do not cut the solar panel wire. Discontinue use if the wire becomes frayed or broken.SAVE THESE INSTRUCTIONS.FOR BEST RESULTS• Allow fixture to receive four full days of sunlight before turning fixture ON.• Locate solar panel in an area that will receive themaximum amount of sunlight during the daylighthours. Locate panel to receive at least 3-4 hours ofdirect sunlight daily.• Test your charged unit before permanently installing.• Install the motion sensor 6-8 feet above the ground.(Motion sensor is less sensitive above 8 feet.)• Locate motion sensor so motion moves across thedetection zone (Fig. 1).• Locate sensor away from heat producing sources to• prevent false triggering. Also be very careful not toinclude objects such as windows, white walls andwater in the detection zone.MSS1301LWA. Light fixture with 12 in. lead wire connectorAccesorio para la luz con conector de cable de 12 pulgLuminaire avec fil de sortie et capuchon de connexionde 30,5 cm (12 po)ENGLISHFig. 1C. (2) Fixture mounting screws(2) Tornillos de montaje del accesorio(2) Vis de montage du luminaireUp to35 feet180 degreesFig. 2ECCFig. 3DBDD DFig. 4BAE. Snap-in mounting bracketSoporte de montaje de sujecióna presiónSupport de montage encastrableB. Solar panel (150x110 mm)with 15 ft. cordPanel solar (150x110 mm)con cable de 15 piesPanneau solaire (150x110 mm)avec cordon de 4,6 m (15 pi)D. (4) Solar panel mounting screws(4) Tornillos de montaje del panel solar(4) Vis de montage de panneau solaire

/ 5

Related manuals for Eaton ALL-PRO MSS1301LW