Eaton ALL-PRO MSS1301LW Instruction Manual

2OPERATING YOUR FIXTURENOTE: Make sure you allow fixture to receive four fulldays of sunlight before turning fixture ON.1. Turn power switch ON.2. Rotate the sensor assembly to reveal the timeadjustment knob. Rotate knob to “TEST”, thenrotate sensor assembly back to desired sensingdirection. (Fig. 5).NOTE: Fixture has a warm up period of about oneminute. Light will turn on during this period. Once thelight turns off, you are ready to test.3. Walk across the detection zone at the farthestdistance you wish your sensor to detect motion.Light will turn off 4 seconds after motion stops.NOTE: Allow 5 seconds after light turns off before yournext test.4. Note location of alignment mark on sensor assembly,then rotate assembly to reveal the time adjustmentknob. Rotate knob to a duration up to 3 minutes, then rotate sensorassembly back to desired sensing direction. Light will turn ON at night when motion isdetected and turn OFF at the selected time interval after motion stops.NOTE: When battery is low, the fixture will automatically turn OFF. (The fixture will not turn ONuntil the battery has recharged to the operating level.)PROPER BATTERY CARENOTE: Proper care should ensure the longest possible life for your battery.• Make sure that your solar panel is located in a sunny location.• When battery is low, the fixture will automatically turn OFF. (The fixture will not turn ON untilthe battery has recharged to the operating level.)• To ensure proper recharge, turn power switch OFF and allow fixture to receive 4 full days ofsunlight before turning the fixture ON.TROUBLESHOOTINGProblem Cause / SolutionLight Does NotCome On WithMotion At NightSurrounding external ambient light is too bright. (If so, the unit maythink it is daytime.)• Re-aim the head.• Relocate or reposition the unit away from the light source.Fixture is not charging during the day.• Solar panel must be connected to the connector extendingfrom the fixture housing when charging.• Solar panel must receive direct sunlight to charge duringthe day (reposition if shadowed).• Solar panel must be clean and free from debris.• Make sure batteries have been charged for 4 full days ofsunlight prior to turning the fixure ON.• When battery is low, the fixture will automatically turn OFF untilthe battery is charged to the operating level.Light Comes OnFor No ApparentReason At NightThere is motion in the detection zone.• Make sure the sensor is not picking up moving objects such astrees, traffic, etc.TEST FOR YOURSELF.• Cover the sensor lens with black electrical tape to preventsensor from detecting motion. If the light stays off, something inthe detection zone is triggering the sensor.• Reposition the sensor.* If the light stays on with the sensor lens covered, contactcustomer service.Light Stays On AtNight And DoesNot Turn OffThere is motion in the detection zone.• Make sure the sensor is not picking up moving objects such astrees, traffic, etc.• Reposition motion sensor.* If the light continues to stay on, contact customer service.Light Is OnDuring The DayThe knob on the motion sensor is in the TEST mode.• Rotate the knob to a duration up to 3 min.The motion detector is shadowed.• Reposition motion sensor.ONE YEAR LIMITED WARRANTYTHE FOLLOWING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES,WHETHER EXPRESS, IMPLIED OR STATUTORY INCLUDING, BUT NOT LIMITED TO, ANYWARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.Eaton warrants to customers that, for a period of one year from the date of purchase, Eatonproducts will be free from defects in materials and workmanship. The obligation of Eatonunder this warranty is expressly limited to the provision of replacement products.This warranty is extended only to the original purchaser of the product. A purchaser’s receiptor other proof of date of original purchase acceptable to Eaton. This is required beforewarranty performance shall be rendered. This warranty does not apply to Eaton products thathave been altered or repaired that have been subjected to neglect, abuse, misuse or accident(including shipping damages). This warranty does not apply to products not manufactured byEaton which have been supplied, installed, and/or used in conjunction with Eaton products.Damage to the product caused by replacement bulbs or corrosion or discoloration of brasscomponents are not covered by this warranty.LIMITATION OF LIABILITY:IN NO EVENT SHALL EATON BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUEN-TIAL DAMAGES (REGARDLESS OF THE FORM OF ACTION, WHETHER IN CONTRACT, STRICTLIABILITY, OR IN TORT INCLUDING NEGLIGENCE), NOR FOR LOST PROFITS; NOR SHALL THELIABILITY OF EATON FOR ANY CLAIMS OR DAMAGE ARISING OUT OF OR CONNECTED WITHTHESE TERMS OR THE MANUFACTURE, SALE, DELIVERY, USE, MAINTENANCE, REPAIR ORMODIFICATION OF EATON PRODUCTS, OR SUPPLY OF ANY REPLACEMENT PARTS THEREFORE,EXCEED THE PURCHASE PRICE OF EATON PRODUCTS GIVING RISE TO A CLAIM. NO LABORCHARGES WILL BE ACCEPTED TO REMOVE OR INSTALL FIXTURES.To obtain warranty service, please contact Eaton at 1-800-334-6871, press option 2 forCustomer Service, or via e-mailConsumerProducts@eaton.com and include the following information:• Name, address and telephone number• Date and place of purchase• Catalog and quantity purchase• Detailed description of problemAll returned products must be accompanied by a Return Goods Authorization Number issuedby the Company and must be returned freight prepaid. Any product received without a ReturnGoods Authorization Number from the Company will be refused. Eaton is not responsible formerchandise damaged in transit. Repaired or replaced products shall be subject to the termsof this warranty and are inspected when packed. Evident or concealed damage that is madein transit should be reported at once to the carrier making the delivery and a claim filed withthem.Reproductions of this document without prior written approval of Eaton’ are strictly prohibited.For assistance, call 1-800-334-6871 or e-mail us at ConsumerProducts@eaton.comPrinted in ChinaARTÍCULOS NECESARIOS(se compran por separado)• Destornillador en cruz (Phillips)CÓMO FUNCIONADurante las horas del día, el panel solar transforma la luzsolar en energía que queda almacenada en el paquete dela bateríarecargable. Su luminaria cuenta con un sensorde movimiento, que enciende la luz cuando es de nochey se detecta algún movimiento. Esta luminaria estáequipada con una fotocélula, que sólo permite que elartefacto se encienda durante las horas de la noche.ADVERTENCIAS Y PRECAUCIONESINSTRUCCIONES CONCERNIENTES AL RIESGO DE INCENDIO O LESIONES ALAS PERSONAS:ATENCIÓN: Para reducir el riesgo de incendio o lesiones personales:• NO sustituya las baterías.• NO deseche este producto por medio de métodos combustibles. Las baterías que seencuentran dentro de este producto pueden explotar o tener pérdidas.Atienda todaslas advertencias.• NO perfore este pack de baterías. NO trabaje sobre este pack de baterías.• NO desarme la luminaria. La luminaria no contiene piezas que puedan recibir un servicio demantenimiento por el usuario.• Para uso en exteriores solamente.• Las baterías de ión de litio deben desecharse de conformidad con las ordenanzas ynormas locales sobre disposición de desechos.• No ponga en funcionamiento esta luminaria si le falta la lente o está dañada.• La luminaria es apta para un montaje en paredes solamente. NO es apta para su instalaciónpor medio de su montaje en el suelo.• No corte el cable del panel solar. Discontinúe su uso si se pela o rompe el cable.GUARDE ESTAS INSTRUCCIONES.ESPAÑOLFig. 5ON OFFAON OFFHasta35 pies180 grados

/ 5

Related manuals for Eaton ALL-PRO MSS1301LW