INSTALLATION – PENDANT MOUNT1. Install the pendant mount bracket with the hardware provided, four (4) ¼-20screws and four (4) ¼-20 nuts (see Figure 1). Center the pendant mountbracket on the luminaire (see Figure 1). Measure from each end of theluminaire to the edge of the pendant mount on each side. The distance fromside to side should be equal or within 1/16” to each other. Tighten the ¼-20screws to 65 in.-lbs. and tighten the 10-24 screws to 21 in.-lbs. DO NOTREMOVE MOUNTING TAB RETENTION SCREWS. If mounting tab retentionscrews are removed, make sure to re-install and tighten to 65 in.-lbs. torque.2. Thread the locknut onto the ¾” NPT conduit threads as far up the threads aspossible.3. Place the luminaire onto the conduit at the hole located in the center of thependant mount bracket. Install the throat bushing onto the conduit and rotatethe luminaire to the correct position. Tighten the throat bushing first (42 ft.-lbs.) and then the lock nut (hand tight plus a quarter turn). After tightening bothwrench tight, tighten the set screw to 9 in.-lbs.4. Remove all four (4) screws from the end cap of the luminaire closest to thewiring entry gland. Install the SOOW cable from the conduit into the cord gripand connect the input wires to the driver input wires of the luminaire accordingto the wiring diagram (see Figure 5). For dimmer applications, remove plugfrom driver housing cover and use a separate cord grip wire according to thewiring diagram (see Figure 5). Tighten cord grip(s) wrench tight to securewires into place. Install the driver housing end cap and tighten the four (4)screws until bottomed.Figure 1 – Pendant Mount Connectiont Secondary retention may be considered for pendant mount applications foradded security and is recommended in applications where high vibrations arepresent. Four (4) additional holes are included on the pendant mount bracketthat may be used for secondary retention and either the aircraft cable (in drylocations) and jack chain mounts are suitable for this purpose.AIRCRAFT CABLE1. Mounting tabs are located 1” from each end of the luminaire from the factory.If mounting tabs need to be relocated or become loose, tighten the 10-24screws to 21 in.-lbs. (see Figure 2) before hanging the luminaire. Mountingtab retention bolts should be tightened to 65 in.-lbs. in all four corners of theluminaire. Mounting tabs should be placed equal distance from the ends ofthe luminaire to ensure the luminaire hangs level.2. Install two (2) aircraft cable assemblies to the luminaire with one aircraft cableassembly at each end of the luminaire as shown in Figure 2. Do not exceedan angle greater than 30° between the cables and the gravity line. Adjustthe length of the aircraft cable assembly to ensure the luminaire hangs level.Mount the luminaire a minimum of 36 inches away from the ceiling. Refer toB-Line FIS-164 Instruction Sheet for further details and information.3. Use the factory installed wire (SOOW cable) for electrical connection to theappropriate junction connection. See WIRING section for more information.WARNINGTo avoid the risk of fire, or electric shock, this product should be installed,inspected and maintained by a qualified electrician only, in accordance with allapplicable electrical codes. *Verify power wire (SOOW cable) is in accordancewith all applicable electrical codes.Industrial High Bay LED LuminairesInstallation & Maintenance InformationSAVE THESE INSTRUCTIONS FOR FUTURE REFERENCEt6- tD6-t*19t4VJUBCMFGPSPQFSBUJPOJOBNCJFOU¡$UP¡$t4VJUBCMFGPSEBNQMPDBUJPOTt$& XIFOPSEFSFEXJUI$&TVGGJY*CE suffix does not include SO cable.CONFIGURATIONSt MVNFOTt MVNFOTt MVNFOTt MVNFOTt MVNFOTt MVNFOTVOLTAGE OPTIONSt6/77"$ 7%$t6/7%7"$ 7%$ EJNNJOHt6/77"$t6/7%7"$ EJNNJOHAPPLICATIONIF 1726*'t $PQZSJHIUª &BUPOT$SPVTF)JOET%JWJTJPO 1BHFWARNINGTo avoid electric shock:Be certain electrical power is OFF before and during installation and maintenance.Luminaire must be supplied by a wiring system with an equipment groundingconductor.To avoid burning hands:Make sure lens and housing are cool when performing maintenance.WARNINGTo avoid product degradation:Do not operate in ambient temperatures above those indicated on the luminairenameplate.Use proper supply wiring as specified on the luminaire nameplate.Avoid use in environments containing sulfur, chlorine or other halides, methylacetate or ethyl acetate, cyanoacrylates, glycol ethers, formaldehyde or butadiene.Mount luminaire no less than 36 inches from ceiling.Make sure the supply voltage is within the voltage range stated on the nameplate.6TFPOMZSFQMBDFNFOUQBSUTGSPN$SPVTF)JOETAircraft cable mounting is recommended for dry locations only.6TFPOMZ$SPVTF)JOETPSFRVJWBMFOUQBSUTGPSNPVOUJOHMVNJOBJSFWARNINGAIRCRAFT CABLE MOUNTING IS INTENDED FOR DRY LOCATIONS ONLY.1/4-20 SCREWS1/4-20 NUTSEQUALDIST.EQUALDIST.LOCK NUTPENDANT MOUNTBRACKETPOWER WIRE(SOOW CABLE)WIRE ACCESSLOCATION(END CAP)CONDUIT10-24 SCREWSMOUNTING TABSDIMMER WIREENTRY LOCATIONMOUNTING TABRETENTION SCREWSEND CAP SCREWSSECONDARYRETENTIONHOLESLock ScrewLock NutThroat Bushing