Eaton Cooper Lightig All-Pro WL2540LP Instruction Manual

1Questions?/ Des questions?/ ¿Preguntas? 1-800-334-6871 ConsumerProducts@cooperlighting.comInstruction Manual / Manuel d’instructions/ InstruccionesPACKAGING CONTENTS/CONTENIDO DEL PAQUETE/CONTENIDO DEL PAQUETEITEMS REQUIRED(Purchase separately)• Adjustable WrenchWARNINGS AND CAUTIONS• Heed all warnings, including below warnings AND those included on product.• Save these instructions and warnings.• For indoor and outdoor use.• cULus LISTED for wet location.• Your LED fixture is prewired. No replacement bulb necessary. Disassembling your fixturewill void the warranty.• Connect fixture to a 120 volt, 60 Hz power source. Any other connection voids the warranty.• Do not look directly at lighted lamp.• Read and follow these instructions.WARNING• Risk of fire/electric shock.• The electrical system, and the method of electrically connecting the fixture to it, must be inaccordance with the National Electrical Code and local building codes.WARNING: When using outdoor use portable luminaires, basic safety precautions shouldalways be followed to reduce the risk of fire, electric shock, and personal injury, includingthe following:Read All INSTRUCTIONS.• Use only three-wire outdoor extension cords that have three-prong grounding plugs andgrounding recptacles that accept the appliance’s plug.• Ground Fault Circuit Interrupter (GFCI) protection is to be provided on the circuit(s) outlet(s)to be used for the wet location portable luminaire. Receptacles are available having built-inGFCI protection and are able to be used for this measure of safety.• Use only with an extrension cord for outdoor use, such as an extension cord of cord typeSW, SW-A, SOW, SOW-A, STW, STW-A, STOW, STOW-A, SJW, SJW-A, SJOW, SJOW-A, SJTW,SJTW-A, SJTOW, SJTOW-A.• Max distance to receptacle is 3 feet.• This equipment has been tested and found to comply with the limits for a Class B digitaldevice, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipmentgenerates, uses and can radiate radio frequency energy and if not installed and used inaccordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. Ifthis equipment does cause harmful interference to radio or television reception, which can bedetermined by turning the equipment off and on, the user is encouraged to try to correct theinterference by one or more of the following measures:- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver.- Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected.- Consult the dealer or an experienced radio/TV technician for help.WL2540LPA. LED WorklightLuminaria LED para sitios de trabajoLampe de travail à DELENGLISHB. StandPie de baseSupportC. (2) M6 Lock WashersArandelas de seguridad M6 (x 2)(2) rondelles freins M6D. (2) M6 x 24mm ScrewsTornillos M6 x 24 mm (x 2)(2) vis M6 de 24 mmWARNING: FCC Regulations state that any unauthorized changes ormodifications to this equipment not expressly approved by the manufacturercould void the user’s authorization to operate this equipment.SAVE THESE INSTRUCTIONS.INSTALLING YOUR FIXTUREWARNING: Deviation from the assembly instructionsmay result in a risk of fire or electric shock.1. Using adjustable wrench (not included) attachworklight (A) with bracket to worklight stand (B)using QTY 2 M6 x 24MM screws (D) and QTY 2 M6lock washers (C) as in (FIG 1).AIMING THE LIGHT1. To aim fixture loosen two knob handles on theside of the worklight (FIG 2). Tilt worklight todesired position and tighten knobs. Worklight canangle 10° degrees down or 90° up (FIG 3). Whentilting worklight 90° up, pass power cord throughhole between stand and worklight to preventwearing power cord (FIG 4).2134CDAB

/ 4

Related manuals for Eaton Cooper Lightig All-Pro WL2540LP