Eaton ALL-PRO Instruction Manual

1Questions?/ Des questions?/ ¿Preguntas? 1-800-334-6871 ConsumerProducts@eaton.comInstruction Manual / Manuel d’instructions/ Instruccionesguarantee that interference will not occur in a particular installation. If thisequipment does cause harmful interference to radio or television reception, whichcan be determined by turning the equipment off and on, the user is encouraged totry to correct the interference by one or more of the following measures:- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver.- Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected.- Consult the dealer or an experienced radio/TV technician for help.WARNING: FCC Regulations state that any unauthorized changes ormodifications to this equipment not expressly approved by the manufacturercould void the user’s authorization to operate this equipment.SAVE THESE INSTRUCTIONS AND WARNINGS.ASSEMBLING YOUR FIXTUREWARNING: Deviation from the assemblyinstructions may result in a risk of fire orelectric shock.1. Using adjustable wrench (not included) attachworklight (A) with bracket to worklight stand (C)using QTY 1 M6 x 12MM screws (H) and QTY 1 M6lock washers (G) as in (Fig. 1).USE AS A STAND LIGHT1. Unlock tripod stand (F) legs first by pulling eachleg out approximately 1 inch, then loosen the knobat the top of the leg assembly and pull legs out,extending to full open position so that the topblack bracket slides down until it is lined up withthe black line on the center pole label (Fig. 2).Retighten knob.2. Attach portable fixture to the tripod stand (F) bypulling out the quick-release knob (B), lining up thepin with the slot, and seating portable light fixtureon tripod (F) (Fig. 3).3. Plug light into a 120 volt receptacle.4. To turn light ON or OFF, push red switch on the backof the fixture (A).5. Adjust the tripod stand (F) to the desired height byloosening and tightening the locking collars onthe pole.Note: Legs must be secured with sand bags or othersuitable weight:• when used on uneven or rocky surfaces• when used in windy areas• anytime extra stability is requiredPACKAGING CONTENTS/CONTENIDO DEL PAQUETE/CONTENU DE L’EMBALLAGEWL2540LSTENGLISHA. Light headCabezal de la lámparaTête de luminaireC. Portable light standSoporte de lalámpara portátilSupport portatif duluminaireB. Quick-release knobPerilla de liberaciónrápidaBouton de déverrouillagerapideF. Tripod standSoporte del trípodeTrépiedD. HandleManijaPoignéeE. Light bracketAbrazadera de la lámparaSupport du luminaireG. (1) Lock washers(1) Arandela de seguridad(1) Rondelles de blocageITEMS REQUIRED(Purchase separately)• Adjustable wrenchINSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK,EXPOSURE TO EXCESSIVE UV RADIATION, OR INJURY TO PERSONS:WARNINGS AND CAUTIONSWARNING: When using outdoor use portable luminaires, basic safety precautionsshould always be followed to reduce the risk of fire, electric shock, exposure to exces-sive UV radiation or injury to persons:WARNING: To reduce the risk of fire, electric shock, exposure to excessive UV radiationor injury to persons:• Heed all warnings, including below warnings AND those included on product.• Your LED fixture is prewired. No replacement bulb necessary. Disassembling your fixturewill void the warranty.WARNING• Risk of fire/electric shock.• The electrical system, and the method of electrically connecting the fixture to it, must be inaccordance with the National Electrical Code and local building codes.• Do not look directly at lighted lamp.CAUTIONREAD ALL INSTRUCTIONS• For indoor and outdoor use.• cULus LISTED for wet locations.• Connect fixture to a 120-volt, 60 Hz power source. Any other connection voidsthe warranty.• Use with only three-wire outdoor extension cords that have three-prong groundingplugs and grounding receptacles that accept the appliance’s plug, such as anextension cord of cord type: SW, SW-A, SOW, SOW-A, STW, STW-A, STOW, STOW-A,SJW, SJW-A, SJOW, SJOW-A, SJTW, SJTW-A, SJTOW, SJTOW-A.• Ground Fault Circuit Interruption (GFCI) protection is to be provided on the circuit(s)or outlet(s) to be used for the wet location portable luminaire. Receptacles areavailable having built-in GFCI protection and are able to be used for this measureof safety.• This equipment has been tested and found to comply with the limits fora Class B digital device, pursuant to Part 15 of the FCC Rules. These limits aredesigned to provide reasonable protection against harmful interference in aresidential installation. This equipment generates, uses and can radiate radiofrequency energy and if not installed and used in accordance with the instructions,may cause harmful interference to radio communications. However, there is noH. (1) Screw(1) Tornillos(1) VisBF3Slide bracketdown to lineup with blackmarks on labelF21GHAC

/ 5

Related manuals for Eaton ALL-PRO