Eaton HALO SLD6 WH Series Instructions Manual
          | |
Contents |
screw base recessed housings. The SLD6 isUL Listed and Classified for retrofit in thefollowing housings:The SLD6 is UL Listed or Classified for use with any 5 or6 inch diameter recessed housing constructed of steelor aluminum with an internal volume that exceeds 107.9cubic inches in addition to those noted below.− HALO®: H7ICAT, H7ICT, H7T, H7ICATNB,H7ICTNB, H7TNB, H7UICAT, H7UICT, H7TCP,H7RICAT, H7RICT, H7RT, H27ICAT, H27ICT, H27T,H27RICAT, H27RICT, H27RT, H5ICAT, H5RICAT,H5T, H5RT, H5TM, H25ICAT− HALO® LED: H750ICAT, H750RICAT, H750T,H750TCP, H2750ICAT, H550ICAT, H550RICAT− HALO® LED Retrofit: ML7BXRFK,ML7E26RFK− ALL-PRO™: EI700, EI700AT, EI700ATNB,EI700U, EI700UAT, EI700NB,EI700R, EI700RAT,ET700, ET700R, EI2700, EI2700AT, ET2700,EI2700R− Juno: IC22, IC22R, IC22W, IC22S, IC23, IC23W,IC21, IC21R, IC2, TC2, TC2R, IC20, IC20R, IC25,IC25R, IC25W, IC25S, TC20, TC20R− Lightolier: 1104ICS*, 1104ICR*, 1104SIC*,1104SICR*, 1004ICS*, 1004ICR*,1004SIC*, 1004SICR*1104ICX - Requires installation of Halo ML7RABretrofit adapter band accessory.− Capri: CR1, PR1, QL1, R9ASIC, R5*− Progress: P87-AT*, P86TG− Lithonia: L7X, L7XP− Thomas: PS1, R9ASIC/PS9RM− Prescolite: IBXS− Commercial Electric: C7ICA (H3), H18− Elco: (HL7ICA) EL7ICA* Requires installation of friction clips (included).Mounting to a junction box:1. Remove 2 retaining screws next to J box mountingbracket from the SLD (see Fig. 2).2. Remove the J box mounting bracket by holding theSLD and rotating the bracket counterclockwise.3. Connect the Supply Wire Adapter to the house supplywire. Using the included wire nuts, connect adapterblack wire to hot supply wire and connect adapterwhite wire to supply neutral wire. Connect theground wire (attached to the bracket) to the groundwire in the junction box using the included wire nuts(Fig. 3).E26 para dar lugar a alojamientos ICAT para baseatornillable estándar. La lámpara retrofit SLD6 esapta para UL y clasificada para lámparas retrofit enlas siguientes alojamientos:Además de los alojamientos indicados a continuación,la luminaria SLD6 tiene certificación o clasificación ULpara su uso con cualquier alojamiento empotrado hechode acero o aluminio, de 5 o 6 pulgadas de diámetro (127mm o 155 mm), con un volumen interno que supere las107,9 pulgadas cúbicas.− HALO®: H7ICAT, H7ICT, H7T, H7ICATNB, H7ICTNB,H7TNB, H7UICAT, H7UICT, H7TCP, H7RICAT, H7RICT,H7RT, H27ICAT, H27ICT, H27T, H27RICAT, H27RICT,H27RT, H5ICAT, H5RICAT, H5T, H5RT, H5TM, H25ICAT− HALO® LED: H750ICAT, H750RICAT, H750T,H750TCP, H2750ICAT, H550ICAT, H550RICAT− HALO® LED Retrofit: ML7BXRFK, ML7E26RFK− ALL-PRO™: EI700, EI700AT, EI700ATNB,EI700U,EI700UAT, EI700NB,EI700R, EI700RAT, ET700,ET700R, EI2700, EI2700AT, ET2700,EI2700R− Juno: IC22, IC22R, IC22W, IC22S, IC23, IC23W,IC21, IC21R, IC2, TC2, TC2R, IC20, IC20R, IC25,IC25R, IC25W, IC25S, TC20, TC20R− Lightolier: 1104ICS*, 1104ICR*, 1104SIC*,1104SICR*, 1004ICS*, 1004ICR*,1004SIC*, 1004SICR*1104ICX - Requiere la instalación del accesorio debanda del adaptador de lámpara retrofitHalo ML7RAB.− Capri: CR1, PR1, QL1, R9ASIC, R5*− Progress: P87-AT*, P86TG− Lithonia: L7X, L7XP− Thomas: PS1, R9ASIC/PS9RM− Prescolite: IBXS− Commercial Electric: C7ICA (H3), H18− Elco: (HL7ICA) EL7ICA* Requiere la instalación de sujetadores de fricción(se incluyen).Montaje en una caja de empalme:1. Quite los dos tornillos de retención contiguos alsoporte de montaje de la caja de empalme desde lalámpara SLD con LED (ver Fig 2).2. Quite el soporte de montaje de la caja de empalmesosteniendo la lámpara y rotando el soporte a laizquierda.acceptant les boîtiers avec culot à vis classiques.Les boîtiers de module SLD6 sont répertoriés etclassés UL pour le module des boîtiers suivants :Le SLD6 est classé ou homologué UL pour être utiliséavec un boîtier encastré de 5 ou 6 pouces fabriquéen acier ou en aluminium avec un volume interne quidépasse 1768,16 cm (107,9 po) en plus de ceux indiquésci-dessous.− HALO®: H7ICAT, H7ICT, H7T, H7ICATNB,H7ICTNB, H7TNB, H7UICAT, H7UICT, H7TCP,H7RICAT, H7RICT, H7RT, H27ICAT, H27ICT, H27T,H27RICAT, H27RICT, H27RT, H5ICAT, H5RICAT, H5T,H5RT, H5TM, H25ICAT− HALO® LED: H750ICAT, H750RICAT, H750T,H750TCP, H2750ICAT, H550ICAT, H550RICAT− HALO® LED Retrofit: ML7BXRFK, ML7E26RFK− ALL-PRO™: EI700, EI700AT, EI700ATNB,EI700U,EI700UAT, EI700NB,EI700R, EI700RAT, ET700,ET700R, EI2700, EI2700AT, ET2700,EI2700R− Juno: IC22, IC22R, IC22W, IC22S, IC23, IC23W,IC21, IC21R, IC2, TC2, TC2R, IC20, IC20R, IC25,IC25R, IC25W, IC25S, TC20, TC20R− Lightolier: 1104ICS*, 1104ICR*, 1104SIC*,1104SICR*, 1004ICS*, 1004ICR*, 1004SIC*,1004SICR*1104ICX - nécessite l’installation d’un collieradaptateur à bande pour boîtier de moduleML7RAB de Halo.− Capri: CR1, PR1, QL1, R9ASIC, R5*− Progress: P87-AT*, P86TG− Lithonia: L7X, L7XP− Thomas: PS1, R9ASIC/PS9RM− Prescolite: IBXS− Commercial Electric: C7ICA (H3), H18− Elco: (HL7ICA) EL7ICA*Nécessite l’installation de colliers de frictions (fournis).Montage sur boîte de jonction :1. Retirez les deux (2) vis de fixation près du support defixation de la boîte de jonction du boîtier de moduleSLD (consultez Fig. 2).2. Retirez le support de fixation de la boîte de jonctionen tenant le boîtier de module et en tournant lesupport vers la gauche.3. Raccordez l’adaptateur du fil d’alimentation auxfils d’alimentation domestiques. Avec le serre-filfourni, raccordez le faisceau électrique noir au filFig. 2Ground Wirele fil de terreel cable a tierraRotate j-box bracket counterclock-wise to remove from SLDTournez la plaque du boîtier dejonction dans le sens contrairedes aiguilles d’une montre pourl’enlever du SLD.Haga girar el soporte de la caja dederivación en sentido antihorariopara retirarla del SLDFor j-box mounting, remove the tworetaining screwsPour monter à une boîte de jonction,retirer les deux vis de fixation.Para el montaje en una caja de conexiones,quite los dos tornillos de sujeción.Fig. 34706087INSCSLD6 Series Instructions www.eaton.com |
Related manuals for Eaton HALO SLD6 WH Series
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine