Eaton HALO WP1050LPC Instruction Manual

Eaton HALO WP1050LPC Instruction Manual Manual pdf 1 page image

Questions?/Des questions?/¿Preguntas? 1-800-334-6871 ConsumerProducts@eaton.com1Instruction Manual/Manuel d’instructions/InstruccionesPACKAGING CONTENTS/CONTENU DE L’EMBALLAGE/CONTENIDO DEL PAQUETESAVE THESE INSTRUCTIONS.FOR BEST RESULTS• Do not mount fixture close to reflective surfacessuch as windows, white walls, white surfacesand water.• When mounting to a wall, make sure the fixtureis 7 in. on center away from eave and 13 incheson center away from inside corner of theexterior wall (Fig. 1).MOUNTING AND WIRING YOUR FIXTUREWARNING: Risk of electric shock. Disconnectpower at fuse or circuit breaker before installingor servicing.NOTE: Back cover mounts to the following types ofrecessed junction boxes: 4 in. square, 4 in. round, 4 in.octagonal, 3-1/2 in. square / octagonal, masonry, 2-3/4in. hole pattern boxes, and single gang outlet.1. Unscrew housing from back cover. Confirm junctionbox mounting screw pattern and ONLY remove thegasket material from the back cover required forinstallation.2. Mount the back cover to the junction box using the#8 screws provided. See (Fig. 2) for proper backcover orientation based on desired lighting direction.3. Caulk around back cover where it contacts themounting surface to provide a watertight seal.4. For downlight applications, temporarily secure thehousing to the back cover using the hanging tabprovided on the back cover (Fig. 3a). For uplightapplications, temporarily secure the housing to theback cover using the tabs provided on the backcover (Fig. 3b).ITEMS REQUIRED(Purchase separately)• Phillips screwdriver• Outdoor weatherproof silicone caulkingIMPORTANT SAFETY INSTRUCTIONSWhen using product, basic precautions should always be followed, including the following:• Heed all warnings, including below warnings AND those included on product.• Save these instructions and warnings.• cULus LISTED for outdoor, wet location use not to exceed 40˚C ambient.• Disassembling your fixture will void the warranty.• Your fixture is prewired and preassembled for easy installation.• Read and follow these instructions.• Risk of fire/electric shock. If not qualified, consult an electrician.• Disconnect power at fuse or circuit breaker before installing or servicing.CAUTION• Connect fixture to a 120 volt, 60 Hz power source. Any other connection voidsthe warranty.• Fixture should be installed by persons with experience in household wiring or by aqualified electrician. The electrical system, and the method of electrically connectingthe fixture to it, must be in accordance with the National Electrical Code and localbuilding codes.• Fixture designed for wall mount to a recessed junction box only. Mount fixture to agrounded standard junction box marked for use in wet locations.• Suitable for mounting within 4 feet of the ground.• Fixture is suitable for ground mounting only when used with optional trunnion mountaccessory kit, catalog number WPFLD-TRN (sold separately).• This device complies with Part 15 of the FCC Rules. Operation is subject to thefollowing two conditions: (1) This device may not cause harmful interference, and (2)this device must accept any interference received, including interference that may causeundesired operation.WARNING: FCC Regulations state that any unauthorized changes ormodifications to this equipment not expressly approved by the manufacturercould void the user’s authorization to operate this equipment.WP1050LWP1850LA. HousingBoîtierAlojamientoENGLISHC. (2) #8-32 x 3/4 in. junction box screws(2) vis nº 8 de 32 x 3/4 po pouboîtier de jonction(2) tornillos #8-32 x 3/4 pulg. para montaje de la caja deconexiónesWARNINGB. Back cover (Preinstalled to housing)Couvercle arrière (préinstallé sur le boîtier)Cubierta trasera (preinstalada en el alojamiento)27in13in113inDownlightUplightDownlight UplightHousing Screw Tab3aC3bWP1050LPCWP1850LPC

/ 4

Related manuals for Eaton HALO WP1050L