Eaton HALO HOME FTS20CW Instruction Manual

Questions?/Des questions?/¿Preguntas? 1-800-334-6871 ConsumerProducts@eaton.com1Instruction Manual/ I n s t r u c c i o n e sPACKAGING CONTENTS/CONTENU DE L’EMBALLAGE/CONTENIDO DEL PAQUETE- Connect the equipment into an outlet on a circuitdifferent from that to which the receiver is connected.- Consult the dealer or an experienced radio/TV technicianfor help.• This device contains transmitter moduleFCC ID: ZAFZ1-AVI1010 (IC ID: 20544-AVI1010)WARNING: FCC Regulations state that anyunauthorized changes or modifications to thisequipment not expressly approved by the manufacturercould void the user’s authorization to operate thisequipment. FCC Radiation Exposure Statement: Theequipment complies with FCC Radiation exposure limitsset forth for uncontrolled enviroment. This equipmentshould be installed and operated with minimumdistance 20cm between the radiator and your body.NOTE: This device complies with Industry Canadalicense-exempt RSS standard(s). Operation is subjectto the following two conditions: (1) this device may notcause interference, and (2) this device must accept anyinterference including interference that may causeundesired operation of the device.SAVE THESE INSTRUCTIONS.FOR BEST RESULTS• Install light 8-16 feet above the ground.• When installing two fixtures on one switch,make sure the switch is rated for at least a1 A inductive load.MOUNTING AND WIRING YOUR FIXTUREWARNING: Risk of electric shock. Disconnectpower at fuse or circuit breaker before installingor servicing.NOTE: Fixture can be wall or eave mounted (Fig. 1).NOTE: Coverplate mounts to recessed mountedstandard junction boxes (Fig. 2). Junction box must beat least 1-1/2 inch in depth for proper installation forrecessed mount application. For surface mount junctionbox installation, refer to installation instructions includedwith the adaptar plate kit (E).1. Line up the holes on the mounting bracket (B) withthe holes on your junction box. Using either (2) #6screws or (2) #8 screws (D) (depending on size ofthe holes in your junction box), attach the mountingbracket (B) to your junction box (Fig. 3).2. Thread fixture wires through mounting bracket (B)and gasket (C) (Fig. 6).ITEMS REQUIRED(Purchase separately)• Phillips screwdriver• Weatherproof silicone caulkIMPORTANT SAFETY INSTRUCTIONSWhen using product, basic precautions should always be followed, including the following:• Heed all warnings, including below warnings AND those included on product.• Save these instructions and warnings.• For outdoor use only.• cULus LISTED for wet location.• Disassembling your fixture will void the warranty.• Your fixture is prewired and preassembled for easy installation.• Read and follow these instructions.• Risk of fire/electric shock. If not qualified, consult an electrician.• Disconnect power at fuse or circuit breaker before installing or servicing.CAUTION• Connect fixture to a 120-277 volt, 50/60 Hz power source. Any other connection voidsthe warranty.• Fixture should be installed by persons with experience in household wiring or by aqualified electrician. The electrical system, and the method of electrically connectingthe fixture to it, must be in accordance with the National Electrical Code and localbuilding codes.• Fixture designed for wall or eave mount to a junction box only. Mount fixture to agrounded, recessed-mounted standard junction box marked for use in wet locations.Fixture can be mounted to an outdoor rated surface mount junction box or when usedwith the included adaptar plate kit. See kit instructions for proper installation methods.NOTE: This equipment has been tested and found to comply with the limits fora Class B digital device, pursuant to Part 15 of the FCC Rules. These limits aredesigned to provide reasonable protection against harmful interference in aresidential installation. This equipment generates, uses and can radiate radiofrequency energy and if not installed and used in accordance with the instructions,may cause harmful interference to radio communications. However, there is noguarantee that interference will not occur in a particular installation. If this equipmentdoes cause harmful interference to radio or television reception, which can bedetermined by turning the equipment off and on, the user is encouraged to try tocorrect the interference by one or more of the following measures:- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver.A. Light fixtureAppareil d’éclairageAccesorioENGLISHD. (2) #6-32 x 3/4 in. and (2) #8-32 x 3/4 in. junction box screws(use the size that fits your junction box)(2) vis nº 6 de 32 x 3/4 po et 2 vis nº 8 de 32 x 3/4 po pouboîtier de jonction (choisissez la dimension convenantà votre boîtier de jonction)(2) Tornillos #6-32 x 3/4 pulg. y (2) tornillos #8-32 x 3/4 pulg.para montaje de la caja de conexión (utilice el tamañoque mejor se adecue a su caja de conexión)F. Support hookCrochetE. FLD-KIT-SFCGNDAdapter Plate KitPlaque adaptatrice troussePlaca daptadora equipoC. GasketJointJuntaH. (2) Decorative screw cover caps(2) cache-vis décoratifs(2) Cubiertas tapatornillos decorativasG. (2) #8-32 x 1-1/4 in. covermounting screws(2) vis de protection nº 8de 32 x 1-1/4 po(2) Tornillos #8-32 x 1-1/4 pulg.de montaje de la cubiertaB. Mounting bracketSupport de montageSoporte de montajeWARNINGFTS20CBFTS20CWHOMETMRound Octagonal1-1/2 in. 1-1/2 in.2FGA5GF3DDJunction boxB1Wall mountEave mountEF4

/ 5

Related manuals for Eaton HALO HOME FTS20CB