Eaton Halo MST18VCW Instruction Manual

Eaton Halo MST18VCW Instruction Manual Manual pdf 1 page image

1Questions?/¿Preguntas? 1-800-334-6871 ConsumerProducts@eaton.comInstruction Manual/InstruccionesPACKAGING CONTENTS/CONTENU DE L’EMBALLAGE/CONTENIDO DEL PAQUETEFOR BEST RESULTS• Install the motion sensor/transmitter 8-12 feetabove the ground. (Motion sensor is less sensitiveabove 12 feet.)• Locate motion sensor so motion moves acrossdetection zone (Fig. 1).• Locate sensor away from heat producing sources toprevent false triggering. Also be very careful not toinclude objects such as windows, white walls andwater in the detection zone.• Locate sensor away from moving objects such astrees, large shrubs and street traffic.• Do not install more than one motion activatedfloodlight on one wall switch.MOUNTING AND WIRING YOUR FIXTUREWARNING: Risk of electric shock. Disconnectpower at fuse or circuit breaker before installingor servicing.NOTE: Fixture can be wall or eave mounted (Fig. 2).NOTE: Coverplate mounts to recessed mountedstandard junction boxes (Fig. 3). Junction box must beat least 1-1/2 inch in depth for proper installation forrecessed mount application.1. Line up the slotted holes on the mounting bracket (B)with the holes on your junction box. Using either (2)#6 screws or (2) #8 screws (D) (depending on size ofthe holes in your junction box), attach the mountingbracket (B) to your junction box (Fig. 4).2. Connect house ground wire to mounting bracketground wire using a wire nut (E) provided (Fig. 4).3. Connect fixture black wire to house black wire, andfixture white wire to house white wire, using the wirenuts (E) provided (Fig. 5).4. Level and secure the mounting bracket arm bytightening the rotation clamp screws and attachfixture (A) to the mounting bracket (B) using (2)decorative cap nuts (D). Be sure no loose wiresremain sticking out from underneath the coverplate(Fig. 5).5. Move the heads to aim light where desired.6. Apply silicone caulk around the edge of thecoverplate to provide a watertight seal from rainand moisture.7. Turn on power at main fuse/breaker box.ITEMS REQUIRED(Purchase separately)• Phillips screwdriver• Outdoor weatherproof silicone caulkingIMPORTANT SAFETY INSTRUCTIONSWhen using product, basic precautions should always be followed, including the following:• Heed all warnings, including below warnings AND those included on product.• Save these instructions and warnings.• For outdoor use only.• cULus LISTED for wet location.• Disassembling your fixture will void the warranty.• Your fixture is prewired and preassembled for easy installation.• Read and follow these instructions.• Risk of fire/electric shock. If not qualified, consult an electrician.• Disconnect power at fuse or circuit breaker before installing or servicing.CAUTION• Connect fixture to a 120 volt, 60 Hz power source. Any other connection voidsthe warranty.• Fixture should be installed by persons with experience in household wiring or by aqualified electrician. The electrical system, and the method of electrically connectingthe fixture to it, must be in accordance with the National Electrical Code and localbuilding codes.• Fixture designed for wall or eave mount to a junction box only. Mount fixture to agrounded, recessed-mounted standard junction box marked for use in wet locations.• Do not mount below 5 feet.• This device complies with Part 15 of the FCC Rules. Operation is subject to thefollowing two conditions: (1) This device may not cause harmful interference, and (2)this device must accept any interference received, including interference that may causeundesired operation.WARNING: FCC Regulations state that any unauthorized changes ormodifications to this equipment not expressly approved by the manufacturercould void the user’s authorization to operate this equipment.SAVE THESE INSTRUCTIONS.MST18VCBMST28VCB(Bronze/Bronze/Bronce)A. Light fixtureAppareil d’éclairageAccesorioENGLISHC. (2) #6-32 x 3/4 in. and (2) #8-32 x 3/4 in. junction box screws(use the size that fits your junction box)(2) vis nº 6 de 32 x 3/4 po et 2 vis nº 8 de 32 x 3/4 po pouboîtier de jonction (choisissez la dimension convenantà votre boîtier de jonction)(2) Tornillos #6-32 x 3/4 pulg. y (2) tornillos #8-32 x 3/4pulg. para montaje de la caja de conexiónes (utilice eltamaño que mejor se adecue a su caja de conexiónes)E. (3) Wire nuts(3) Serre-fils(3) Tuercas para cablesD. (2) Decorative cap nuts(2) Écrous borgnes décoratifs(2) Tuercas decorativasB. Mounting bracketSupport de montageSoporte de montaje2AWall mountEave mount4 B2BRound1-1/2 in.Octagonal1-1/2 in.3MST18VCWMST28VCW(White/Blanc/Blanco)1