GE GLD2800T Owner's Manual

Also see for GLD2800T: Installation instructions Dimensions and installation information

Contents

11Consumer SupportTroubleshooting TipsOperating InstructionsSafety InstructionsSPEED CYCLE 7.5 gal., 35–70 min.(on some models) This cycle is for everyday dishes and glassware.RINSE ONLY 2.5 gal., 10 min.For rinsing partial loads that will be washed later. Do not use detergent with this cycle.nOTE: This dishwasher is equipped with a cleansensor™ with automatic temperature control; therefore, cyclelength and time may vary depending on soil and temperature conditions.nOTE: only the SAnI WASH cycle has been designed to meet the requirements of section 6, nsF 184 for soilremoval and sanitization efficacy.OptionsThe light above the selected pad will be On to indicate which EnHAnCEMEnT/ExTrA has been selected.STEAM For use with heavily soiled and/or dried-on, baked-on soils. This option MuST be selected prIOr(on some models) to starting the cycle. The STEAM option adds 24 minutes to the cycle time.HEATED DRY When HEATEd dry is off, dishes will air dry.light oFFHEATED DRY Turns the heater on for faster drying. This will extend the total cycle time betweenlight on 8 and 38 minutes depending on the cycle selected. nOTE: HEATEd dry cannot beselected with rInSE Only cycle.LOCK You can lock the controls to prevent any selections from being made. or you can lockthe controls after you have started a cycle.children cannot accidentally start dishwasher by touching pads with this option selected.To unlock the dishwasher controls, touch and hold the HEATEd dry pad for 3seconds. The light above the lOCK pad will turn off. To lock the dishwasher control,touch and hold the HEATEd dry pad for 3 seconds. The light above the lOCK padwill turn on.ADDED HEAT When selected, the cycle will run with heating element on longer and may increasecycle times to improve both wash and dry performance.nOTE: Cannot be selected with rInSE Only cycle.DELAY HOURS You can delay the start of a wash cycle for up to 9 hours. Touch the dElAy HOurS padto choose the number of hours you want to delay the start of the cycle; then touchSTArT/rESET. The machine will count down and start automatically at the correct time.Touching STArT/rESET a second time will cancel the dElAy STArT selection.nOTE: If you forget to fully close the door, a reminder signal will beep until you do so.RESET To change a cycle after washing starts, touch the STArT/rESET pad to cancel thecycle. For some models, the STArT/rESET light will flash while the water is pumpedout. This takes approximately 90 seconds. The door must be closed to complete pumpout. When the light stops flashing, the dishwasher can be reprogrammed andrestarted. Buttons will not respond during pump out.For other models, the STArT/rESET lEd will turn off and the drain pump will pumpwater out of the dishwasher for 90 seconds and then turn off. Cycle selection andoption lEd’s will remain on, and buttons will respond during pump out. If theSTArT/rESET is pressed while the dishwasher is in pump out, the STArT/rESET lEdwill turn on and the dishwasher will start a new wash cycleGEAppliances.com4STArT Close and latch the dishwasher door and select the cycle and desired enhancements. Touch theSTArT/rESET pad once to begin the cycle. Water begins to fill the dishwasher, and approximately 60seconds later the wash action begins.nOTE: The dishwasher remembers your last cycle so you don’t have to reprogram each time. When thedishwasher door is fully closed, the control panel lights will display the last settings you selected.If you don’t want to change any of the settings, simply touch the STArT/rESET pad to begin the cycle.If the door is closed, the indicator lights will turn off if the STArT/rESET pad is not selected within twominutes. To activate the display, open and close the door or press any pad.Also, if a power failure occurs, nOrMAl WASH and HEATEd dry will automatically be programmed.Make any new selections and touch the STArT/rESET pad to begin the cycle.ClEAn The ClEAn light will illuminate and a double beep will sound when a wash cycle is complete. On somemodels, the ClEAn light will turn off when the door is opened. On other models, the ClEAn light willremain on until the door is opened and then relatched or until any keypad is pressed while the door islatched shut.56