GE GLD2800T Owner's Manual

Also see for GLD2800T: Installation instructions Dimensions and installation information

Contents

9Consumer SupportTroubleshooting TipsOperating InstructionsSafety InstructionsGEAppliances.comOptionsThe light above the selected pad will be On to indicate which OpTIOn has been selected.HOT START/ For use with heavily soiled and/or dried-on, baked-on soils. This option MuST beSTEAM selected prIOr to starting the cycle. This option will improve both wash and dry(on some performance. This option adds 20 minutes to the cycle time.models) nOTE: Cannot be selected with rInSE Only cycle.HEATED DRY Shuts off the drying heat option. Dishes air dry naturally and energy is saved.light oFF For faster air dry you can prop the door open after the ClEAn light illuminates.HEATED DRY Turns the heater on for fast drying. This will extend the total run time by 38 minutes.light on nOTE: Cannot be selected with rInSE Only cycle.LOCK You can lock the controls to prevent any selections from being made. or you can lockthe controls after you have started a cycle.(on some children cannot accidentally start dishwasher by touching pads with this optionmodels) selected.To LOCK the dishwasher control, touch and hold the HEATEd dry pad for 3 seconds. The light belowthe HEATEd dry pad will turn on. To UNLOCK the dishwasher control, touch and hold the HEATEddry pad for 3 seconds. The lOCK light will turn off.HOT WASH/ When selected, the cycle will run longer with the heating element on to improve bothADDED HEAT wash and dry performance. For use with heavily soiled and/or dried-on soils. Thisoption MuST be selected prIOr to starting the cycle. nOTE: Cannot be selected withrInSE Only cycle.DELAY HOURS You can delay the start of a wash cycle for 2, 4 or 8 hours (delay time options may varyby model). Touch the dElAy HOurS pad to choose the number of hours you want todelay the start of the cycle; then touch STArT/rESET one time. The dishwasher willcount down and start automatically at the correct time. Touching STArT/rESET asecond time will cancel the dElAy STArT selection.RESET To change a cycle after washing starts, touch the STArT/rESET pad to cancel thecycle. For some models, the lEd’s indicating selected cycle and options will flash whilethe water is pumped out. This takes approximately 105 seconds. When the lights stopsflashing, the dishwasher can be reprogrammed and restarted. Buttons will not respondduring pump out.For other models, the lEd’s indicating the selected cycle and options will flash and thedrain pump will pump water out of the dishwasher for 105 seconds and then turn off.Buttons will respond during pump out. If any button is pressed during the pump out,the lEd’s will stop flashing and indicate new cycle or options selected. If theSTArT/rESET button is pressed while the dishwasher is in pump out, the dishwasherwill start a new wash cycle.Start Close and latch the dishwasher door and select the cycle and desired enhancements.Touch the STArT/rESET pad once to begin the cycle. Water begins to fill thedishwasher, and approximately 60 seconds later the wash action begins.nOTE: The dishwasher remembers your last cycle so you don’t have to reprogram eachtime. When the dishwasher door is fully closed, the control panel lights will display thelast settings you selected.If you don’t want to change any of the settings, simply touch the STArT/rESET padonce to begin the cycle.If the door is closed, the indicator lights will turn off if the STArT/rESET pad is notpressed within two minutes. To activate the display, open and close the door or touchany pad.Also, if a power failure occurs, nOrMAl WASH and HEATEd dry will automatically beprogrammed.34