GE PSXH47 Installation Instructions Manual

Also see for PSXH47: Owner's manual

Contents

GE PSXH47 Installation Instructions Manual Manual pdf 8 page image

85. Run the dryer through a cycle check for proper operation.NOTE: On gas dryers, before the burner will light, it isnecessary for the gas line to be bled of air. If theburner does not light within 45 seconds the firsttime the dryer is turned on, the safety switch willshut the burner off. If this happens, turn the timerto "OFF" and wait 5 minutes before making anotherattempt to light.6. If your dryer does not operate, please review the "Avoid ServiceChecklist" located in your Use and Care Guide before calling forservice.7. Place these instructions in a location near the dryer for futurereference.NOTE: A wiring diagram is located inside the dryer console or underthe top panel.REPLACEMENT PARTSPedestalA pedestal accessory, Model No. NLPWD15, specifically designed for thisdryer may be used when elevating the dryer for ease of use. Failure to useaccessories certified by the manufacturer could result in personal injury,property damage or damage to the dryer.If replacements parts are needed for your dryer, contact the sourcewhere you purchased your dryer.Label all wires prior to disconnection when servicingcontrols. Wiring errors can cause improper and dangerous operation.Verify proper operation after servicing.Destroy the carton and plastic bags after the dryer isunpacked. Children might use them for play. Cartons covered withrugs, bedspreads, or plastic sheets can become airtight chamberscausing suffocation. Place all materials in a garbage container or makematerials inaccessible to children.The instructions in this manual and all other literatureincluded with this dryer are not meant to cover every possible conditionand situation that may occur. Good safe practice and caution MUST beapplied when installing, operating and maintaining any appliance.VALVE OPEN / GAS FLOW POSITIONGAS CONNECTION1. Remove the shipping cap from gas pipe at the rear ofthe dryer.NOTE: DO NOT connect the dryer to L.P. gas service withoutconverting the gas valve. An L.P. conversion kit must be installed by aqualified gas technician.2. Connect a 1/2 inch (1.27 cm) I.D. semi-rigid or approved pipe fromgas supply line to the 3/8 inch (0.96 cm) pipe located on the back ofthe dryer (see pages 6 and 7). Use a 1/2 inch to 3/8 inch (1.27 cm to0.96 cm) reducer for a connection. Apply an approved threadsealer that is resistant to the corrosive action of liquefied gases onall pipe connections.3. Open the shutoff valve in the gas supply line to allow gas to flowthrough pipe.4. Test all connections by brushing on a soapy water solution. NEVERtest for gas leaks with an open flame.GENERAL INSTALLATION1. Connect the exhaust duct to outside exhaust system (see pages 3and 4). Use duct tape to seal all joints.2. With the dryer in its final position, adjust one or more of the legsuntil the dryer is resting solid on all four legs. Place a level on top ofthe dryer. The dryer MUST be level and resting solid on all fourlegs.3. Plug the power cord into a grounded outlet. NOTE: Check toensure the power is off at circuit breaker/fuse box before pluggingthe power cord into the outlet.4. Turn on the power at the circuit breaker/fuse box.Before operating the dryer, make sure the dryer areais clear and free from combustible materials, gasoline, and otherflammable vapors. Also see that nothing (such as boxes,clothing, etc.) obstructs the flow of combustion and ventilationair.POWER CORDTIGHTEN NUTTO THESETHREADSSTRAINRELIEFMOUNTINGBRACKETGREENGROUNDSCREWNUTNEUTRALGROUNDWIRESILVERTERMINAL7. Tighten the screws securing the cord restraint firmly against the powercord.8. Tighten the strain relief nut securely so that the strain relief does notturn.9. Reinstall the terminal block cover.4. Thread a U.L. approved 30 amp power cord, NEMA 14-30 type ST orSRDT through the strain relief.5. Attach the green power cord ground wire to the cabinet with thegreen ground screw.6. Attach the white (neutral) power cord conductor from the power cordand the neutral ground wire from the dryer harness to the silver-colored center terminal on the terminal block. Tighten the screwsecurely.7. Attach the red and black power cord conductors to the outer brass-colored terminals on the terminal block.Do not make a sharp bend or crimp wiring/conductor at the connections.8. Tighten the screws securing the cord restraint firmly against the powercord.9. Tighten the strain relief nut securely so the strain relief does not turn.10. Reinstall the terminal block access cover.ELECTRICAL CONNECTIONSFOR 4-WIRE SYSTEMSTRAINRELIEFMOUNTINGBRACKETNUTTIGHTENNUTTO THESETHREADSPOWERCORDREDWHITEBLACKTERMINALBLOCKSILVER TERMINALGREENGROUNDSCREWGREEN POWER CORDGROUND WIRENEUTRALGROUNDWIRENON-CANADIAN ELECTRIC Dryer1. Remove the screws securing the terminal block access cover andthe strain relief mounting bracket located on the back of the dryerupper corner.2. Install a U.L. approved strain relief in the entry hole of the mountingbracket. Finger tighten the nut only at this time.3. Remove the ground wire from the green ground screw locatedabove the terminal block.REDBLACKWHITEGREEN30 AMP NEMA 14-30 TYPE SRDT OR STTYPICAL 4CONDUCTOR TYPICAL 4CONDUCTOR