Garmin Camper 785 Owner's Manual

Also see for Camper 785: Owner's manual

3 Select a file.4 Select Edit > Copy.5 Browse to a folder on the device.NOTE: For a removable drive or volume, you should notplace files in the Garmin folder.6 Select Edit > Paste.Disconnecting the USB CableIf your device is connected to your computer as a removabledrive or volume, you must safely disconnect your device fromyour computer to avoid data loss. If your device is connected toyour Windows computer as a portable device, it is not necessaryto safely disconnect the device.1 Complete an action:• For Windows computers, select the Safely RemoveHardware icon in the system tray, and select your device.• For Apple computers, select the device, and select File >Eject.2 Disconnect the cable from your computer.Power CablesYour device can be powered various ways.• Vehicle power cable• USB cable• AC adapter (optional accessory)Charging the DeviceNOTE: This Class III product shall be powered by an LPS powersupply.You can charge the battery in the device using any of thesemethods.• Install the device in the mount, and connect the mount tovehicle power.• Connect the device to an optional power adapter accessory,such as a wall power adapter.You can purchase an approved Garmin AC-DC adaptersuitable for home or office use from a Garmin dealer orwww.garmin.com. The device may charge slowly whenconnected to a third-party adapter.Changing the Fuse in the Vehicle Power CableNOTICEWhen replacing the fuse, do not lose any of the small piecesand make sure they are put back in the proper position. Thevehicle power cable does not work unless it is assembledcorrectly.If your device does not charge in your vehicle, you may need toreplace the fuse located at the tip of the vehicle adapter.1 Rotate the end piece counter clockwise to unlock it.TIP: You may need to use a coin to remove the end piece.2 Remove the end piece, the silver tip , and the fuse .3 Insert a new fast-blow fuse that has the same current, suchas 1 A or 2 A.4 Place the silver tip in the end piece.5 Push in the end piece and rotate it clockwise to lock it backinto the vehicle power cable .Installing the RV Charging StationAccessoryNOTICEFailure to heed these installation requirements could result indamage to the product or vehicle.• You must choose a suitable mounting location for thecharging station before drilling holes in the vehicle wall.• You must verify the mounting surface allows the mount to besecurely connected and the mounting screws will notinterfere with wiring or features in the wall.• You must use proper mounting screws for your vehicle's wallmaterial. The included screws are intended for installation onwood or fiberglass walls. Before installing the screws, youmust verify the screws are the correct length and will notdamage the exterior walls or any other components.To install the RV charging station accessory, you need a Philipsscrewdriver and a drill with a 1.5 mm (1/16 in.) drill bit.The RV charging station accessory provides a permanent, wall-mounted charging station for your device. This allows you to useand charge the device in the living area of your RV.1 Place the mount against the wall, and use the six screw holesto mark the pilot-hole locations.2 Remove the mount from the surface.3 Using a 1.5 mm (1/16 in.) drill bit appropriate for the wallmaterial, drill a pilot hole in each of the six locations youmarked.NOTICEDo not drill through the mount. This could result in damage tothe mount or wall.4 Line up the screw holes on the wall mount with the pilotholes, and secure the mount to the wall using six screws.5 Press the socket in the device mount onto the ball of the wallmount until it snaps into place.6 Route the bare-wire connectors to the RV battery or a 12 Vpower source.7 Connect the black wire to the negative (-) terminal of thebattery, and connect the red wire to the positive (+) terminalof the battery.Appendix 25