Gemini 7854T User Manual

Also see for 7854T: Installer manual User manual

Contents

Gemini 7854T User Manual Manual pdf 4 page image

PAG.6 PAG.7ALARM OPERATION WITH BASIC CONFIGURATIONPressing the (dotted) button #1 on the remote control or inserting the electronickey into the receptacle will activate the alarm.This action is indicated by one long flashing of the turn signals, two shortacoustic signals and the permanent turning on of the LEDis indicated by two acoustic signals andtwo turn signals flashes.When the engine block is activated the LED flash quickly.It’s sufficient to turn the vehicle ignition key in “ON” position and press onebutton of the remote to disarm the passive engine immobiliser.During alarm activation, should the seat or the trunk be opened, the alarm willsignal the failure by means of a low-tone beep (BOOP) after the alarm armingsignalling.In any case the alarm will be activated and, at the end of the "neutral time", analarm condition will be generated.When the activation signals are finished, the alarm goes in standby or neutral-time condition, which is signalled with a steady-light LED.This time duration is about 20 seconds.The engine immobilization function and the connectors for optional modulesare already active.uring the first 4 seconds in neutral time, the alarm siren can be deactivated,by simply pressing (smooth) button #2 on the remote control.Siren deactivation will be signalled by a short flashing of the turn signals.When the siren is deactivated, the alarm signals will change correspondingly.Indeed only visual signals will be active, i.e. with flashing of the turn signals, butthe engine immobilization function will still work.Trunk openlifted-up seat signallingArmingEngine passive armingNeutral timeExcluding the siren.The passive engine immobiliser is actived from the system 40” after the turn-offof the vehicle.Lifting up the seat or opening the trunk (if the supplementary button is installed)during the 40” of the immobiliser pre-arming, the time count will be cancelledand restarts when the seat or the trunk are closed.The engine immobiliser is also actived after 40” by remote disarming.In both cases engine passive armingDThe siren sound exclusion is bound to the single arming cycle.NOTEExcluding the built-in sensorDuring the first 4” of neutral time, it is possible to exclude the alarm built-insensor (lifting); to do this, you must just put the electronic key into the specificreceptacle, after the alarm system has been activated.The exclusion is bound to a single arming cycle and will be indicated by a shortflashing of the status led.Armed conditionAlarmLimiting the acoustic signal:.Turn on the ignition key ( )..!!!!!!!!!At the end of the neutral time, after about 20 seconds, the alarm goes in thearmed condition and signals this with a blinking led.From now on, the alarm is ready to signal possible attempts to force thevehicle.If, during the alert state, should occur any theft attempt against the vehicle, thealarm will signal this by activating the high-volume siren, lighting up the red ledwith a steady light and causing the direction indicators to flash repeatedly forabout 30 seconds.The alarm may be activated by different causes, which also depend on theactivated functions described belowCut-off of the power supply cablespositive under keyShifting attemptOpening of the seat or the trunk.Panic alarm, by pushing (smooth) button #2 on the remote controlWhen the alarm conditions are over, the system will revert to the alert state.During the alarm condition it is still possible to deactivate the siren by pushingbutton #2 (smooth) on the remote control (without disarming the alarm).Alarm conditions caused by shock, shifting/hitting, seat or trunk opening, willbe signalled by the activation of the siren for 8 times.From the sixth alarm condition on, the siren will cease to be active.This deactivation of the siren is performed because of these simple reasons:Observance of the regulations in force in the subject of acoustic emissionscaused by vehicle alarms.Power saving, to maximize the vehicle battery.It is no use keeping the alarm on if, after 8 acoustic signals, nobody iscoming to check the vehicle.Noise pollution reduction, to prevent penalties as the regulations in force.Once the alarm cycle is over, the device will ignore any other alarm cause foreight seconds, while keeping the led steadily on.After this interval, the LED will start blinking again.Neutral time between two alarm signals

/ 7

Related manuals for Gemini 7854T