Gemini GEM-P816 Installation Instructions Manual

Also see for GEM-P816: Datasheet Installation instructions Installation instructions

Gemini GEM-P816 Installation Instructions Manual Manual pdf 22 page image

X GEM-P816 Installation Instructions L NAPCO Security SystemsWI994C 3/04! Page 22Basic Operation: Zone Descriptions to Arming in Away ModeButtons G0 will clear the entry at the cursor. When programming zone descriptions, buttons 3 and6 will scroll not only through numbers 0-9, but through the alphabet and a series of punctuation marks andsymbols as well. (Roughly note the order in which the letters, numbers and symbols are displayed so that you will beable to determine the proper direction to scroll, up or down, for fastest access. As familiarity improves, so willprogramming speed). When the description has been entered and is satisfactory as displayed (e.g. ìGARAGEî), youMUST press the U or D button to save it in memory.To advance to the next zone (or to any other zone, for that matter), position the cursor over the displayed Zone Number,i.e., ì01î using buttons 1 and 2. Change the Zone Number using buttons 3 and 6. Repeat thezone-description programming procedure for the new zone. Advance to the next zone and repeat until all zones (up to32 zones) have been programmed.ARMING AND DISARMING THE SYSTEMIn the normal disarmed state, only the green STATUS LED will be on and the display will read ìSYSTEM READYî. To silencean alarm, enter any User Code, then press the U or D button. Any valid User Code may be used to arm or disarm; anArm-Only Code may only be used to arm.Arming! To arm, enter a valid User Code, then press the D button. (For all "Classic GEM-RP keypads)! To arm, enter a valid User Code, then press the Q button. (For all "K Series" keypads)(If a wrong code is entered, the keypad will display ìINVALID ENTRY / TRY AGAINî). The green STATUS LED will go off, thered ARMED LED will go on, and the display will read ìPLEASE EXIT IN / XXX SECONDSî (ìXXXî representing the programmedexit-delay time, in seconds). The exit delay will immediately start counting down toward ì000î, in 10-seconddecrements, indicating the available time remaining to exit through an exit/entry door. Note: If a System Trouble isdisplayed, there should be an attempt to correct the system trouble (for example by calling an alarm maintenance or analarm repairman). If this cannot be done, then press the C button to allow 5 minutes to access the keypad withoutthe system trouble display. Immediate attention should be provided, when system troubles are encountered.DisarmingWhen the exit time has elapsed, the display will read ìSYSTEM ARMEDî. This indicates that upon entering the premisesthrough an exit/entry door, there will be an entry delay to allow time to disarm the panel. The GEM-RP1CAe2 or GEM-K1CA display will read ìDISARM NOW / XXX SECONDSî (ìXXXî representing the programmed entry-delay time, in seconds). Thesounder will come on and the entry delay will immediately start counting down toward ì000î in intervals of 10 seconds,indicating the available time remaining to disarm the panel. (Note: The sounder will "pulse" with the GEM-P9600/3200version 30 and above, and with the GEM-P1632/816 version 10 and above. The sounder will sound a "steady" tonewith the GEM-P9600/3200 version 20 and lower, and with the GEM-P1632/816 version 9A and lower). The sounder willemit a pulsing warning tone during the final 10 seconds.To disarm the panel, enter a valid User Code, then press the U or D button.Arming in AWAY MODEAWAY MODE provides for full protection of the perimeter and interior zones. Exit/Entry doors are provided with Exit/Entry delays. A "Classic" (non "K Series") keypad will display ìSYSTEM ARMEDî, while a "K Series" keypad will displayìARMED AWAY.î The RED LED will remain ON. With "K Series" keypads such as the GEM-K1CA and the GEM-K2AS, press Q to begin the exit delay process (the exit delay will immediately start counting down toward ì000î, in10-second decrements, indicating the available time remaining to exit through an exit/entry door).Arming in STAY MODESTAY MODE provides partial protection by allowing free movement within the premises, while still protecting the perimeterzones. Exit/Entry doors are provided with Exit/Entry delays. A "Classic" series keypad will display ìSYSTEM ARMEDî with aBypass Icon and a RED LED that remains ON, while a GREEN LED blinks. With "K Series" keypads such as the GEM-K1CAand the GEM-K2AS, pressing the STAY button bypasses all interior zones simultaneously, and arms the panel in "STAYMODE". The keypad will display "ARMED STAY". If the STAY button is pressed when the panel is already armed in STAYMODE, the panel will enter "Instant Mode" and eliminate the entry time delay period.