Gemini GEM-P816 Installation Instructions Manual

Also see for GEM-P816: Datasheet Installation instructions Installation instructions

Gemini GEM-P816 Installation Instructions Manual Manual pdf 26 page image

X GEM-P816 Installation Instructions L NAPCO Security SystemsWI994C 3/04! Page 26KEYPAD MESSAGESThe GEM-RP1CAe2/GEM-K1CA Keypads can display the below messages. The GEM-RP2ASe2/GEM-K2AS will display similarabbreviated messages that may scroll through two screens. Note: See page 7 for a listing of the keypad specific User Guides avail-able. These User Guides contain more details regarding the various keypad messages.SYSTEM READY - All zones operating; system can be armed. 1through 2 = Area.ARMING YYY/XXX SECONDS - Exit delay in progress. XXX = exittime remaining in 10-second decrements; YYY = AWAY orSTAY. Arming then becomes ARMED.DISARM NOW/XXX SECONDS - Entry delay in progress. XXX =entry time remaining in 10-second decrements.SYSTEM ARMED - Panel armed. GEM-RP1CAe2/GEM-K1CA key-pads only.ZONE FAULTED - One or more zones not secured. Display statusfor zone description(s). GEM-RP1CAe2/GEM-K1CA only.CAN'T ARM SYSTEM/ZONE FAULTED - Arming attempted withPriority Zone in trouble. Secure zone to arm.DAY ZONE TROUBLE - Trouble condition on Day Zone, followed byone or more zone descriptions.INVALID ENTRY/TRY AGAIN - Wrong code/time/area numberentered.CAN'T ARM SYSTEM/PRESS RESET KEY - Arming attempted withSystem Trouble present. Press the C button and then armthe system.ALARM - Alarm condition, followed by one or more zonedescriptions.FIRE ALARM - Alarm condition on a Fire Zone. Enter your codethen press the U button to silence the sounder. Correct thecause of the alarm, then press the C button again. Firealarm condition, followed by one or more zone descriptions.SYSTEM TROUBLE - A System Trouble display will be followed byone or more of the following error codes:AC POWER FAIL/E01-00 SERVICE. Power failure. Checkpower transformer. Check for blown fuse or circuit breaker;general power outage.LOW BATTERY/E02-00 SERVICE. Battery below 11 volts. If notrecharged within 24 hours, replace it.COMM FAIL/E03-00 SERVICE. Unsuccessful communication tocentral station. Note: Will also display if panel improperlyprogrammed to report; i.e., Report Alarm, Report Codes,Subscriber ID Numbers, etc. must be programmed.WIRELESS TROUBLE/04-NN SERVICE. Wireless transmittersupervisory failure. NN = transmitter number.WIRELESS LOWBATT/E05-NN SERVICE. Rf transmitter lowbattery. NN = transmitter number.SYSTEM TROUBLE/E06-NN SERVICE. Rf receiver responsetrouble. NN = receiver number.SYSTEM TROUBLE/E07-00 SERVICE. Download failure.SYSTEM TROUBLE/E08-00 SERVICE. Telephone line failure(system trouble displays after a fixed 60 second delay).SYSTEM TROUBLE/E09-00 SERVICE, NO PANEL PROGRAM.System cold start not programmed after address 1198.SYSTEM TROUBLE/E10-NN SERVICE. Keypad responsefailure. NN = keypad number.SYSTEM TROUBLE/E11-NN SERVICE. Keypad tamper coverremoved. NN = keypad number.SYSTEM TROUBLE/E12-NN SERVICE. Expansion zone modulefailure. NN = module number.SYSTEM TROUBLE/E13-NN SERVICE. EZM module coverremoved. NN = module number.SYSTEM TROUBLE/E14-NN SERVICE. Relay board responsefailure. NN = relay board number.SYSTEM TROUBLE/E15-NN SERVICE. Wireless transmittertamper cover removed. NN = transmitter number.SYSTEM TROUBLE/E16-NN SERVICE. Receiver jammed. NN= receiver number.SYSTEM TROUBLE/E17-NN SERVICE. Receiver coverremoved. NN = receiver number.SYSTEM TROUBLE/E18-NN SERVICE. Key fob RF transmitterlow battery. NN = key fob transmitter number.SYSTEM TROUBLE/E19-00 SERVICE. Internal user memoryerror. Select RESET SYSTEM TBL. Press the U button,then the C button.SYSTEM TROUBLE/E20-00 SERVICE. Internal dealer memoryerror.SYSTEM TROUBLE/E21-NN SERVICE. Check GEM-PrinterModule, printer out of paper or printer off-line.SYSTEM TROUBLE/E22-NN SERVICE. No trip detected on PIRSupervision Zone within programmed Sensor-Watch time. NN= Zone number. To reset, press NEXT/YES button at ìRESETSENSOR MSGî function display.SYSTEM TROUBLE/E23-00 SERVICE. Failure of 4-wire bus.Check Terminals 11/12.SYSTEM TROUBLE/E27-00 SERVICE. Printer Failure. Call in-stalling company for service.SYSTEM TROUBLE/E39-00 SERVICE. Receiver capacity error.SYSTEM TROUBLE/E40-00 SERVICE. RF Self-Test failure.SYSTEM TROUBLE/E41-NN SERVICE. Trouble condition on aFire Zone. Press C button to silence the sounder.Correct the trouble, then press the C button again.(GEM-P1632 and GEM-P816 panels only).SYSTEM TROUBLE/E51-00 SERVICE - Alarm OutputSupervisory.SYSTEM TROUBLE/E58-00 SERVICE. Telemetry Trouble. Callinstalling company for service.SYSTEM TROUBLE/E59-00 SERVICE. Telemetry Failure. Callinstalling company for service.SYSTEM TROUBLE/E66-00 SERVICE. "Clean Me" warning--Smoke Detector dirty. Clean detector or call installing com-pany for service.SYSTEM TROUBLE/E99-00 SERVICE. Keypad Panic shortedtoo long (RP2/K2 and RP3/K3 keypads).NN OUT OF SYSTEM - Keypad inoperative. NN = keypadnumber.FAULT FIND/RF SIGNAL POWER - Fault-find Mode activated.Keypad Messages