Gemini KIT Parking Sensor 818W Installation And Use Manual
PAGE 04 - USER MANUAL USER MANUL - PAGE 05To time-activate the sensors, a parameter must be be modified (see chapter “setting ofparameters).When the setting is modified, the OFF sign is not displayed when the left hand sidepush-button is pressed because the sensors will automatically activate when ignition isturned on again.Engagement of the reverse gear activates the rear sensors but also the front sensors ifthey are programmed to work on a “time-activation” basis.On some vehicles, when speed exceeds 10Km/h, no icon could be displayed eventhough the system is active.The sensors can still be deactivated with the push-button.The front sensors are activated by turning on ignition; an upward arrow icon will light up on the displayto indicate activation.directly related to the setting of theTo deactivate the sensors, simply press the display left-hand side push-button; the upward arrow iconon the display will turn offtime setting preset time delay “0”Functioning is parameters..By modifying the of the front sensors (function 13, ), the front sensorswill work as follows:If, within the preset time, no obstacle is detected in front of the vehicle, the sensors willautomatically be deactivated.If, within the preset time, the obstacle is still detected, the sensors will remain active as long as theobstacle is detected and will deactivate 3” after detecting the last obstacle.If you need to use the front sensors again after the automatic deactivation, simply press the leftpush-button.The sensors will automatically deactivate 3” after detecting the last obstacle.!!!2.2 - REAR SENSORSThe rear sensors are activated when reverse gear is engaged; an audible signal.To reactivate them, simply press the same buttonwarning and thedownward arrow icon that lights up on the display will indicate the sensors are active.Obstacles are signaled by different audible tones and the lighting up of the relative detection zonesand distance on the display.The faster the beeping, the closer the obstacle; a continuous tone indicates the obstacle is extremelyclose to the bumper.To deactivate the sensors (when reverse gear is engaged), simply press the push-button on the righthand side of the display; the “OFF” sign will light up on the bottom part of the displayed vehicle and thedownward arrow will turn off to indicate the sensors are deactivated.In case of need (vehicles in queue), press the push-button with the upward arrow to deactivate thesensors.In this case the “OFF” sign will light up on the displayed vehicle.2.3 -.AUTOMATIC ACTIVATION OF FRONT SENSORS (odometer signal)Front sensors are activated whenever ignition is turned ON and are automatically deactivated whenspeed exceeds about 15Km/h3.0 - TROUBLESHOOTING GUIDE3.1 - LOW POWER SUPPLY SIGNALIf, when the system is turned on, the battery level is too low to guarantee the accuracy of the system,).after a few seconds, the following icons will be displayed: vehicle, front sensors arrow icon and fourfront detection zones closest to the bumper.The arrow and the detection zones icons will flash for about 8/10 seconds.This will inform the driver that ALL sensors are deactivated and that he will have to carry out reversingand parking manoeuvers without the help of the sensors.When nominal tension is restored, the rear sensors will start working normally.To activate the front sensors, cut and restore supply to the front control unit (turn ignition off and on2.4 - )TIME-ACTIVATED FRONT SENSORS (odometer not connected3.2 - FRONT.).SENSORS ANOMALY INDICATIONIf one of the sensors turns out to be inoperative or disconnected, a few seconds after the control unit isturned on, the following icons will be displayed: vehicle, front sensors arrow and inoperative sensor (orsensors)If parameter 13 has not been modified and is set to “0”, the front sensors arrow and detection zoneswill flash as long as the control unit remains active.If, on the other hand, parameter 13 has been modified, the front sensors arrow and detection zoneswill flash for about 8/10 seconds.All other sensors will operate normally.If one of the rear sensors turns out to be inoperative when reverse gear is engaged, the front sensorsarrow and inoperative sensor (or sensors) icon will flash as long as reverse gear is engaged (and 8/10seconds after reverse is disengaged3.3 -.REAR SENSORS ANOMALY INDICATIONIf one of the sensors turns out to be inoperative or disconnected, a few seconds after reverse gear isengaged, the following icons will be displayed: vehicle, rear sensor arrow and inoperative sensor (orsensors).The arrow and the icon relative to the inoperative sensor will flash as long as reverse is engaged; allother sensors will work normallyRear sensor 5inoperative;sensor iconflashes.Front sensor 1inoperative;sensor iconflashes. |
Related manuals for Gemini KIT Parking Sensor 818W
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine