Gemini KIT Parking Sensor 818W Installation And Use Manual

Contents

Gemini KIT Parking Sensor 818W Installation And Use Manual Manual pdf 6 page image

PAGE 06 - USER MANUAL USER MANUAL - PAGE 07Clean the sensorsUse the angle brackets (11 or 14) to tilt axe of sensors upwardsCreate a separation between sensor and vehicle (at least 2mm)Modify the setting of parameter 11SOLUTIONIce on sensorsSensors mounted too lowBack part of sensors in contact with frameSensors detect external spare wheelPOSSIBLE CAUSE3.4 - OTHERSACTIVATION/DEACTIVATION OF REAR SENSORS,SETTING OF OVERSPEED INDICATOR,SCROLLING AND SETTING OF FUNCTIONSOn every button press, the rear sensors will beactivated/deactivated.The downward arrow will be displayed when thesensors are activated..A..CTIVATION/DEACTIVATION OF FRONTSENSORS, TURNING OFF OVERSPEEDINDICATOR, SCROLLING AND SETTING OFFUNCTIONSOn every button press, the front sensors will beactivated/deactivated.The upward arrow icon will be displayed whenthe sensors are activatedSENSORSDEACTIVATEDINDICATION ICONS(FRONT OR REAR).SENSORSACTIVATEDINDICATION ICONS(FRONT OR REAR).DISTANCE OF OBSTACLEINDICATORPARAMETER.STATUS (F or C) ANDSETTING OF PARAMETER..VEHICLE SPEED.SOFTWARE VERSION.FRONT SENSORSACTIVATEDINDICATION ICONS.REAR SENSORSACTIVATEDINDICATION ICONS.“STOP” ZONE ICON.5.0 - DISPLAYThe following icons will be displayed according to operations.S .ETTING MODECONTROL UNITS/DISPLAYSIGNAL RECEPTION TEST.RF DISTURBANCES.AUDIBLE WARNINGSON/OFF ICON.7.0 - WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT(WEEE) DIRECTIVEThe present device does not fall within the scope of Directive 2002/96/EC on Waste Electrical andElectronic Equipment (WEEE) as specified in art. 2.1 of L.D. no. 151 of 25/07/2005.6.0 - WARRANTY CONDITIONSThis product is guaranteed to be free from defects in workmanship for a period of 24 months from thedate of installation reported on this warranty, in compliance with the 1999/44/CE Warranty Directive(L. D. N° 24 of the 02/02/2002).Please fill-in entirely the guarantee certificate included in this booklet and DO NOT REMOVE theguarantee label from the device.The warranty will become void if labels are missing or torn, if the installation certificate is not fullycompiled or if the enclosed sale document is missing.The warranty is valid exclusively at authorized Gemini Technologies centers.The manufacturer declines any responsability for eventual malfunctions of the parking sensors or anydamage to the vehicle electrical system due to improper installation, use or tampering.The parking system is strictly a parking assist device, it should not be considered to be a safety devicefor any purpose.In areas with high RF disturbances, the antenna icon will light up on the display and aticking sound will be heard.If the disturbance affects the rear control unit, it will deactivate within a few seconds (thedownward arrow icon will turn off).If the disturbance affects the front control unit, it will deactivate within a few seconds(the upward arrow icon will turn off) but the continuous “STOP ZONE” alert will sound.Press the left push-button on the display to stop the beeping and deactive the sensors.This procedure can only be done if the relative cable of the display wiring is connectedto the odometric signal of the vehicle; check with your installer.4.0 - SETTING OF OVERSPEED AUDIBLE ALERT!!!!Turn the ignition “ON”.13.0 and 14.0), s 14, select value 2 and15 km/h.Turn ignition key “OFF” then “ON” and increse speed..Enter in the programming mode (see chap. elect parameterset it by keeping one of the two display buttons pressed for about 3 sec.; by activating this functionthe display and the speed value will light up every time speed exceedsLook at the speed displayed; when the required threshold is reached to set the overspeed audiblealert, press the right-hand display buttonA series of audible signals will now sound every time the vehicle exceeds the registered speed .To deactivate this function press the left-hand display button when speed exceeds 15km/h; anaudible signal will indicate deactivation.To reactivate this function and set another threshold, press the right-hand side button (even if thespeed is higher than the one actually set, the system will register this last value).!!!