HAI Omni Pro II Owner's Manual

Also see for Omni Pro II: Installation Installation manual Quick reference Installation manual

Contents

HAI Omni Pro II Owner's Manual Manual pdf 39 page image

Page 31Scene Off CommandOnce the Scenes have been sent, press the 0 (OFF) key to command the four units in that Scene to turn off.Notes:1. When sending Scene Commands, the controller must be configured to allow Extended Code transmissions on each HouseCode affected by a Scene.2. The Scene Commands always apply to a group of four consecutive units, which are units 1-4, 5-8, 9-12, and 13-16 on aparticular house code. You must address the units accordingly so that the desired units fall into the appropriate lightinggroups.3. The actual Extended Code Scene commands use a "group reference" that matches that sent by a Leviton Wall-MountedScene Controller set to the same address as the first unit in the lighting group. This allows wall-mounted controllers to beeasily used for manual Scene selection.UPB LinksIn a UPB network, all control operations are done using Links. OmniPro II can transmit and receive up to 250 Links on the UPBnetwork. Links are used to logically “connect” events on one or more devices to actions on one or more other devices. When twoor more different devices share a common Link, they are said to be “linked” together. They can now communicate with eachother over the powerline using the Link as a common identifier in all of their communications.The power of Links is that you can “link” more than two devices together. For example, one keypad controller pushbutton can belinked to four UPB Wall Switches allowing the single press of that pushbutton to trigger all four lights to go to preset or absolutelevels. In addition UPB Wall Switches allow for a preset light level and fade rate to be associated with each Link.Activating and Deactivating LinksA special UPB command called “Link On” (activate) is used to command all of the devices that have the same Link to go to theirpreset light levels at their preset fade rates.For instance, in our “All On” and “All Off” example, when “Link 50 On” is transmitted by OmniPro II, each UPB Wall Switchwith Link 50 will go to 100% to achieve the “All On” effect. Other “Link On” (activate) commands may be transmitted thatcause Wall Switch ‘1’ to go to a desired level at a specified fade rate and Wall Switch ‘2’ to go to a different level at a differentfade rate. The ability to send more than one device to its preset level at a preset fade rate with a single command is known asactivating a Link. Likewise, pressing a pushbutton on a 6-Button or 8-Button Keypad can send the “Link On” (activate)command.A special UPB command called “Link Off” (deactivate) is used to command all of the devices that have the same Link to go to0% at their preset fade rate. For instance, in our “All On” and “All Off” example, when “Link 50 Off” is transmitted by OmniProII, each Wall Switch with Link 50 will go to 0% to achieve the “All Off” effect.Setting a Link (Lighting Scenes)Lighting scenes are created by pre-configuring light levels and fade rates in one or more UPB devices that get “activated” and“deactivated” by a Link command or button press on a 6-Button or 8-Button Keypad.Each UPB Wall Switch can hold up to sixteen different preset light levels (0% - 100%) that can be “linked” to the OmniPro IIcontroller or to a pushbutton on a 6-Button or 8-Button Keypad.OmniPro II can “set” each of the 250 possible Links. The “Link Set” command is used to set up lighting scenes for a lightinggroup. To set a “lighting scene” using OmniPro II, adjust all of the UPB Wall Switches with the pre-configured Link to thedesired lighting levels. The desired lighting levels may be set manually at the switch, or by a command issued from OmniPro II.After the desired lighting levels are set, the “Link Set” command can be transmitted by OmniPro II to save the new “light levels”for each of the devices pre-configured with the specified Link.