Haier LY26R3A Instruction Manual

Also see for LT26K3: Instruction manual

Haier LY26R3A Instruction Manual Manual pdf 3 page image

GET TO KNOW YOUR TV WITH DVD17.OPTICALFront control panel1. YPbPr input2. YPbPr AUDIO input3. DVI AUDIO input4. ANTENNA input5. HDMI3 input6. S-VIDEO input7. EARPHONE output8. HDMI1 input9. HDMI2 input10.AV-VIDEO input11. Common Interface12.SCART1 input13.VGA AUDIO input14.SCART2 input15.VGA input16.USBSource buttonMenu buttonVolume up/downbuttonProgram up/downbuttonPower buttonUSB21RECCOMPONENT INHDMI3VGA INANT INRear Terminals ControlWhen using the remote control, aim ittowards the remote sensor on the TV Stand ByDVD Menu / RECDVD open / closePicture ModeSound ModeCall Screen DisplaySleep buttonDTV Audio / NICAM / DVD AudioAspect Ratio Control buttonChannel list buttonSubtitle buttonProgram Number Channel selectionSource ExchangeQ.VIEW / Swap ChannelV+/V- : Volume selectionP+/P-: Channel selectionMuteMenu buttonGUIDE button (only for DTV)Favourite list buttonOK buttonCursor Mover buttonBack button (only for USB)Exit Screen DisplayREPEAT (only for DVD , USB , REC & Timeshift) /CANCEL buttonZoom (only for DVD &USB)/Teletext index(only forTV) / REC indexPlay / Pause button (only for DVD &USB) / TimeshiftStop (only for DVD, USB, REC & Timeshift)Fast Reverse (only for DVD, USB, REC & Timeshift)Fast Forward (only for DVD, USB, REC & Timeshift)Previous (only for DVD, USB, REC & Timeshift)Next (only for DVD, USB, REC & Timeshift)DVD Set up / TextDVD Title / Teletext MixDVD Search / Teletext SubcodeDVD 10+ / Teletext HoldDVD Program / Teletext RevealDVD A-B Repeat / Teletext SizeDVD Call / Teletext ModeDVD Angle /Teletext TimeNOTE:RED button ,GREEN buttonBLUE button and YELLOW button are fasttext button in analog signal .Functionbutton in DVBT (just reference the OSD)SCREENSCREENSTOPSTOP.GET TO KNOW YOUR REMOTE CONTROLL R Y Pb PrDVDCONNECTING YOUR TVANTENNA CONNECTIONConnect your aerial to the side of the TV into the ANTENNA IN socket.IMPROVE YOUR SIGNALTo improve picture quality in a poor signal area, use a signal amplifier(not supplied).CONNECT YOUR PC TO THE TVYou can use your TV as a monitor for your personal computer by connecting itwith a VGA cable (not supplied).1.Read your computer user guide and check it has a VGA connector.2.Turn the power off on your TV and PC.3.Connect a D type 15-pin VGA interface cable to the VGA video interfaceconnector on the PC. Connect the other end of the cable to the PC interfaceconnector on the TV. Tighten the screws on the VGA connectors and connectthe audio cable (not supplied) to the audio input socket on the back of the TV.4.Turn on the power of the TV firstly and then the PC.5.Press the button on the TV or TV remote control to set the video input modeto VGA.6. Once the image shows, if there is noise present, change the VGA mode toanother resolution, change the refresh rate to another rate or adjust thebrightness and contrast on the menu until the picture is clear.CONNECT A DVD PLAYER TO YOUR TVConnect the DVD video outputs (Y, Pb, Pr) to theCOMPONENT (Y, Pb, Pr)IN socket on your TV.1 . Turn on the DVD player and insert a DVD.2 . Press the button to select .3 . Refer to the DVD player user guide for operatinginstructions.CONNECT A DVD PLAYER OR VCR TO YOUR TVThere are two ways in which you can connect a DVD player or VCR to your TV.Make sure that both the TV and DVD player or VCR are switched off before youconnect them.Connection Option 11.Connect the audio and S-VIDEO cables from the VCR output jacks to the TVinput jacks.2.Insert a video tape into the VCR and press PLAY on the VCR.3.Turn on the power of the TV first, then the VCR.4.Press the SOURCE button on the TV to set the video input mode to S-VIDEO.Connection Option 21.Connect the AV DVD/VCR outputs to the AV IN socket on your TV.2.Press the SOURCE button on the TV to set the video input mode to AV.SCART INPUT1.Connect the scart lead from the external device (DVD player, Set-top boxor games console) to the TV scart socket.2.Press the SOURCE button to select SCART mode.3.Press the PLAY button on the external device.HDMI INPUT1.Connect the cable from the HDMI device to the TV HDMI socket.2.Press the SOURCE button to select HDMI mode.3.Refer to the HDMI device user guide for how to operate.MOUNT YOUR TV ONTO THE WALLYou can mount your TV onto the wall by using a wall bracket (not supplied).Use M4/M6 machine screws (4 pcs) to screw the TV onto the bracket (notsupplied).