Harman Kardon AVR45 Owner's Manual

Also see for AVR45: Owner's manual Service manual

Harman Kardon AVR45 Owner's Manual Manual pdf 16 page image

Remote Control Functionsn Memory Button: Press thisbutton to enter a radio station intothe AVR45’s preset memory. Afterpressing the button the MEMORYindicator N will flash, and you thenhave five seconds to enter a presentmemory location using the NumericKeys l. (See page 26 for moreinformation.)NOTE: Although the word “Sleep”appears above this button, it refersto control of devices other than theAVR45. Use the Sleep button ` tocontrol the AVR45’s Sleep function.o Info Button: This button doesnot function with the AVR45, but it isavailable for use with other devices.p Light Button: Press this buttonto activate the remote’s built-in back-light for better legibility of the buttonsin a darkened room.q Tuner Mode: Press this buttonwhen the tuner is in use to selectbetween automatic tuning andmanual tuning. When the button ispressed so that the AUTO indicatorO goes out, pressing the Tuningbuttons t will move the frequencyup or down in single-step incre-ments. When the FM band is inuse, pressing this button when astation’s signal is weak will changeto monaural reception, as indicatedby the MONO indicator Q. (See page26 for more information.)r Clear Button: This button doesnot function with the AVR45, but it isavailable for use with other devices.s Preset Up/Down: When thetuner is in use, these buttons scrollthrough the stations that have beenprogrammed into the AVR45’s mem-ory. When many source devices,such as CD players, VCRs and cas-sette decks, are selected using theDevice Control Selectors b,these buttons will normally functionas chapter step or track advance.t Tuning Up/Down: When thetuner is in use, these buttons willtune up or down through the select-ed frequency band. If the TunerMode button q has been pressedso that the AUTO indicator O is illu-minated, pressing these buttons willcause the tuner to seek the next sta-tion with acceptable signal strengthfor quality reception. When the AUTOindicator O is NOT illuminated,pressing these buttons will tune sta-tions in single-step increments. (Seepage 26 for more information.)u Transport Controls: These con-trols do not control any functions ofthe AVR45, but they are used exten-sively when operating a wide varietyof CD players, cassette decks andVCRs. (See page 28 for informationon programming the remote to utilizethese buttons.)v Delay/Prev Ch.: Press this but-ton to begin the process for settingthe delay times used by the AVR45when processing surround sound.After pressing this button the delaytimes are entered by pressing theSet button i, and then using the⁄ / ¤ buttons g to change the set-ting. Press the Set button again tocomplete the process. (See page 20for more information.)w ›/Digital Button: This button isused to select the type of digital inputused with any one of the input sourcesconnected to the AVR45. After press-ing this button, use the ⁄ / ¤ buttonsg to make your selection betweenOPTICAL E or COAXIAL G digital.Press the Set button i to enteryour choice. (See page 24 for moreinformation.)x Speaker Configuration: Pressthis button to begin the process ofconfiguring the AVR45’s BassManagement System for use withthe type of speakers used in yoursystem. Once the button has beenpressed, use the ⁄ / ¤ buttons g toselect the channel you wish to set up.Press the Set button i, and thenselect another channel to configure.When all adjustments have beencompleted, press the Set buttontwice to exit the settings and returnto normal operation. (See page 17for more information.)y Surround Mode Selector: Pressthis button to begin the process ofchanging the surround mode. Afterthe button has been pressed, usethe ⁄ / ¤ buttons g to select thedesired surround mode. (See page24 for more information.) Note that thisbutton is also used to tune channelswhen the TV is selected using theDevice Control Selector b.When the AVR45 remote is being pro-grammed for the codes of anotherdevice, this button is also used in the“Auto Search” process. (See page 28for more information on programmingthe AVR45 remote.)z Volume: Press these buttons toraise or lower the system volume.` Sleep Button: Press this buttonto place the unit in the Sleep mode.After the time shown in the display,the AVR45 will automatically go intothe Standby mode. Each press ofthe button changes the time untilturn-off in the following order:Note that this button is also usedto change channels on your TVwhen the TV is selected using theDevice Control Selector b.When the AVR45 remote is being pro-grammed for the codes of anotherdevice, this button is also used in the“Auto Search” process. (See page 28for more information on programmingthe AVR45 remote.)90min 80min 70min 60min 50min 40min30min 20min 10min 5min 1min OFF13