Harman Kardon DPR 1001 Service Manual

Also see for DPR 1001: Brochure Brochure & specs Brochure & specs Brochure Brochure

Contents

Harman Kardon DPR 1001 Service Manual Manual pdf 5 page image

A) ANALOG INPUT, BASELINE AUDIO PARAMETERS (STEREO SURROUND MODE)Measuring methods are based on IHF and IEC standard 268-3Measurement conditions,unless otherwise noted :Tone Off or Tone(Bass,Treble), Balance, EQ control : Center Position , Other SW's : OFF, Volume:MaxNominal input level : 0dBFS sine wave PCM bitstream (Digital), 225mV sine wave (Analog)Power figures should be kept minimum 10min., between 15 and 35 oC .Terminator : 1kohm for general purpose inputsAll Voltage Measurements are made with RMS detector, unless otherwise specified.Filter : IHF-A filterUUT= Unit Under Test.Power supply : 120 V , 60 HzMARKETING UNIT RATINGS. CONDITION UNIT VALUEWatts/Ch 50Watts/Ch 50Ohm8 ohm, +/-1 %,Non-Inductive,455 WSPEAKER AVAILABLE SPEAKER MODES*SUB-WOOFER SPKR:YES *SPKR LEVEL:ALL 0dB *TONE OUTSPEAKER POWER AMPLIFIER SECTION1 1kHz2 VOL at min. 10Hz-22KHz BW, peak detector, all inputsterminated w/ 1 Kohm mVpk <3mV <2mVVOL at min. 10Hz-22KHz BW, peak detector, all inputsterminated w/ 1 Kohm mVpk <2.5mV <1.5mVVOL at max. 10Hz-22KHz BW, peak detector, all inputsterminated w/ 1 Kohm mVpk <10mVpk <8mVpkVOL at max. 10Hz-22KHz BW, peak detector, all inputsterminated w/ 1 Kohm mVpk <4mVpk <2.5mVpkVOL at max. 10Hz-22KHz BW, RMS , non-weighted, all inputsterminated w/ 1 Kohm mVrms <4mVrms <3mVr msVOL at max. 10Hz-22KHz BW, RMS , non-weighted, all inputsterminated w/ 1 Kohm mVrms <1mVrms <0.75mVr msVOL at max. 10Hz-22KHz BW, RMS , 'A Weighted', all inputsterminated w/ 1 Kohm mVrms <3mVrms <2.5mVr msVOL at max. 10Hz-22KHz BW, RMS , 'A Weighted', all inputsterminated w/ 1 Kohm mVrms <0.7mVrms <0.5mVr msVOL at max. 10Hz-22KHz BW, RMS , 'A Weighted', all inputsleft un-terminated mVrms <3mVrms <2.5mVr msVOL at max. 10Hz-22KHz BW, RMS , 'A Weighted', all inputsleft un-terminated mVrms <0.7mVrms <0.5mVr ms8CHSTEREO8 CHSTEREO8 CHSTEREO8 CHSTEREO8 CHSTEREO8 CHSTEREO20Hz1k20k225±40 225±20<0.6 <0.45Rated Stereo Power OutputRated 8 CH DIRECT Power OutputRated Resistive LoadBoth FL and FR Speaker amplifiers driven and loaded with RatedResistive Load.All Seven (FL,FR,C,SL,SR,SBL,SBR) Speaker amplifiers driven andloaded with Rated Resistive Load Impedance.Resistive loads to be connected to Speaker Outputs using a 12 AWGStranded Speaker Wire pair for each load resistor. Wire length shouldbe approximately 10 feet.LARGE ALWAYSYES/NOInput SensitivityFRONT "L" AND "R" SPEAKERSSUBWOOFER OUTPUTRESIDUAL NOISETOTALHARMONICDISTORTION(Rated StereoPowerOutput -1dB)Should be met byall Stereo InputsStereo and 8 CH DIRECT rated Power into Rated ResistiveLoad should be obtained by applying an input signal levelwith the specified range.mVShould be met byall Analog Stereoand 8CH DIRECTInputs20Hz-20 KHz,Power out =RatedPower - 1 dBShould be met byall Analog Stereoand 8 CH DIRECTInputsVol at Max, 10 Hz-22KHz Meas BW."A"WEIGHTED %LIMIT NOMONALNo DESCRIPTION INPUT FREQ. REMARK UNIT5DPR1001 harman/kardonDETAILED SPECIFICATIONS