Harman Kardon RCP 7 Owner's Manual

Also see for CP 65: Brochure & specs Catalog

Contents

The following keys on the RCP 7 remote may be programmed withindividual IR codes that are “learned” from another remote control:Power On/Off, Mute, Sleep/Audio and DSP Surround/Title (ChannelUp/Down), Volume Controls, Channel Level/Disc Menu, Speaker/DVDSetup, Digital Input/Drawer Open/Close, Delay/DVD Status, ‹ › ⁄¤Navigation, Set/Enter, Numeric Keys, Track Skip Up/Down and TransportControls – a total of 34 buttons.Follow these steps to learn individual key codes:1. Place the RCP 7 and the device’s original remote so that their IRtransmitters face each other end to end, separated by about oneinch (see Figure 3). The RCP 7 remote’s transmitter also serves asan IR receiver during the learning process.Figure 3 – RCP 7 and Original Remote, Head to Head2. Make sure the RCP 7 is in the device mode you want to learnthe new key code for by pressing the Input Selector, which shouldlight in red, or green if it is a secondary source on a dual-sourceselector. If necessary, press a dual-source selector twice to selectbetween the primary and secondary sources. Place the RCP 7remote in Learning mode by pressing and holding the Learn Buttonuntil the Program Indicator flashes amber, then releasing it (seeFigure 4).Figure 4 – Learning Remote Commands3. On the RCP 7 remote, press and hold the button you wish to programwith the new code until the Program Indicator remains steadily lit inamber, then release it.4. On the device’s original remote, press and hold the button whosecode you wish to “learn” until the RCP 7’s Program Indicator flashesgreen, then release it.5. You may program additional buttons by repeating Steps 3 and 4.To exit Learning mode, press the Learn Button once. If you prefer,you may wait for the remote to “time out” and exit Learning modeon its own, but this will take about 30 seconds.If you make a mistake while learning a code, you may either learna new code over the old code, or else erase the learned code, whichreturns the button to the code in the original code set that youprogrammed into the Input Selector. To erase a single learned code:1. Make sure the RCP 7 is in the device mode containing the learnedcode you wish to erase by pressing the Input Selector, which shouldlight in red, or green if the secondary source on a dual-sourceselector is active.2. Press and hold the Learn Button until the Input Selector lights andthe Program Indicator flashes amber, then release it.3. Press the Input Selector again and release it.4. Enter the code “777” by pressing the “7” Numeric Key three times.The Input Selector should flash each time.5. Press the button whose learned code you wish to erase and release.The Program Indicator will flash green to confirm the erasure.6. Repeat Step 5 for any other buttons whose learned codes you wishto erase.7. Press the Learn Button to exit Learning mode, or wait about 30seconds for Learning mode to time out.To erase all of the learned codes for a device mode:1. Make sure the RCP 7 is in the device mode containing the learnedcode you wish to erase by pressing the Input Selector, which shouldlight in red, or green if the secondary source on a dual-sourceselector is active.2. Press and hold the Learn Button until the Input Selector lights andthe Program Indicator flashes amber, then release it.3. Press the Input Selector again and release it.4. Enter the code “888” by pressing the “8” Numeric Key three times.The Input Selector should flash each time. The Program Indicatorwill flash green to confirm the erasure.To erase all of the learned codes on the remote for all device modes,but without erasing other user settings such as product code sets orpunch-through programming, follow these steps:1. Press and hold the Learn Button until the last-used Input Selectorlights in red and the Program Indicator flashes amber, then release it.2. Press any Input Selector and release it.3. Enter the code “999” by pressing the “9” Numeric Key three times.The Input Selector should flash each time. The Program Indicator willgo dark, and the Input Selector you pressed in Step 2 will remain lit forabout 10 seconds. Then the Program Indicator will flash green to con-firm the erasure, and the remote will automatically exit Learning mode.12LEARNING INDIVIDUAL KEY CODES