4REMOTE CONTROL FUNCTIONSThe RCP 7 remote is capable of controlling 11 devices, including theAVR 347 and the DVD 48 included in the CP 65 system. During theinstallation process, you may program the codes for each of your sourcecomponents into the remote. Each time you wish to use the codes forany component, first press that component’s selector. This changes thebutton functions to the appropriate codes for that product.NOTE: Several of the Input Selectors are shared between twodevices. The selector button will light in red when the remote is inthe device mode printed on the button, and it will light in green forthe device mode printed above the button. To switch between thetwo device modes, press the selectortwice quickly in succession.The selector will remain in the last-selected mode until the nexttime you press it twice quickly.For example, the first time you press the DVD Button, the buttonwill light in red, indicating that the remote is in DVD mode. If youpress another selector, such as the VID3 Selector, and then pressthe DVD Button again, the DVD Button will remain red, indicatingthe remote is still in DVD mode. Now press the DVD Button twicequickly. At the first press the Button will light in red, indicating thatthe remote is in DVD mode. On the second press the button willturn green, indicating that the remote is now in CD mode. If youpress a different selector and return to the DVD/CD Selector, youwill observe that the remote is still in CD mode.Each Input Selector has been preprogrammed to control certain typesof components, with only the codes specific to each brand and modelchanging, depending on which product code is programmed. Thedevice types programmed into each selector (except HDMI 1 and 2)may not be changed.DVD: Controls DVD players and recorders. The DVD Button functionsare labeled in blue on the remote.CD: Controls CD players and recorders.Tape: Controls cassette decks.The Bridge/DMP: Controls an iPod device docked in The Bridge.Video 1: Controls VCRs, TiVo® boxes and DVRs.Video 2: Controls cable and satellite television set-top boxes.Video 3: Controls televisions and other video displays.Video 4: Controls a TV connected to the front-panel inputs.HDMI™ 1 and 2: Each code set controls a source device (such asa VCR/PVR/DVD player or cable/satellite set-top box) connected toone of these two inputs.XM: Controls the AVR functions for XM Satellite Radio.For example, if you have inserted a disc in your CD player and youwould like to skip ahead three tracks, but you then find that the volumeis too loud, you would follow this procedure:1. Press the CD Input Selector to switch to the codes that control yourCD player. If the remote is in DVD mode, press the selector twicequickly to switch to CD mode, indicated by the selector turning green.2. Press the Play Button (in the Transport Controls section) if the discis not already playing.3. Press the Skip Up Button three times to advance three tracks.4. Press the AVR Button so that you can access the volume controls.5. Press the Volume Down Button until the volume level is satisfactory.Any given button may have different functions, depending on whichcomponent is being controlled. The buttons are labeled with some ofthese functions, with the receiver’s functions shown in gray, and theDVD player’s functions shown in blue. For example, the Sleep and DSPSurround Buttons are labeled for use as Channel Up/Down Buttonswhen controlling a television or cable box. See Table A1 in the Appendixfor listings of the different functions for each type of component.NOTE: Although we have described the applicable DVD functionsin this section, we strongly recommend that you review theDVD 48 manual for more information about using these functions.IR Transmitter Lens: As buttons are pressed on the remote,infrared codes are emitted through this lens. Make sure it is pointingtoward the component being operated.Power On Button: Press this button to turn on the AVR or anotherdevice. The Master Power Switch on the AVR 347’s front panel mustbe switched on first.Mute Button: Press this button to mute the AVR 347’s speaker andheadphone outputs temporarily. To turn off muting, press this buttonor adjust the volume. Muting is also canceled when the receiver isturned off.Program Indicator: This LED lights up or flashes in one of three colorsas the remote is programmed with codes.Power Off Button: Press this button to turn off the AVR 347 oranother device.AVR Selector: Press this button to switch the remote to the codesthat operate the receiver.Input Selectors: Press one of these buttons to select a sourcedevice, which is a component where a playback signal originates (e.g.,DVD, CD, cable TV, satellite or HDTV tuner). This will also turn on thereceiver (if it is not already on) and switch the remote’s mode to operatethe source device.AM/FM Button: Press this button to select the tuner as the source,or to switch between the AM and FM bands.6-/8-Channel Input Selector: Press this button to select the6-/8-Channel Inputs as the audio source. The receiver will use the videoinput and remote control codes for the last-selected video source.