Contents - electrical safety
- trademarks and service marks
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- maintenance overview
- hanzi printers
- printer evolution
- important maintenance notes
- notes and notices
- printing conventions in this manual
- controls and indicators
- electrical controls, pedestal models
- mechanical controls, all models
- tools, test equipment, and supplies
- installing and configuring the ibm 6400 printer
- preventive maintenance
- cleaning the interior
- cleaning the shuttle frame assembly
- cleaning the card cage fan assembly
- principles of operation
- printing rates
- shuttle frame assembly
- paper transport system
- ribbon transport system
- logical control of the printer
- operator panel
- cmx controller board
- data controller
- engine controller
- printer interface
- base2 and 10base-t leds and dip switches
- dip switches
- power supply board
- troubleshooting
- start of call
- troubleshooting display messages
- message list
- troubleshooting other symptoms
- general symptom list
- communications failures
- operator print tests
- selecting and running tests
- shuttle speed
- boot diagnostics menu
- hex code printout
- ascii character set
- printer information menu
- displaying printer information
- soft reset
- the power on sequence
- dc software initialization and power up
- adjustment procedures
- preparing the printer for maintenance
- returning the printer to normal operation
- belt, paper feed timing, adjustment
- belt, platen open, adjustment
- paper drive motor pulley alignment
- paper scale alignment
- platen gap adjustment
- platen open motor pulley alignment
- ribbon guide alignment
- splined shaft skew adjustment
- adjusting the end of forms distance
- hammer phasing adjustment
- downloading 6400 microcode from the world wide web
- loading flash memory
- coil temperature adjustment
- set shuttle speed
- ethernet initialization
- replacement procedures
- list of procedures
- belt, paper feed timing
- belt, platen open
- circuit board: controller
- circuit board: power supply
- circuit breaker
- coax/twinax multi-platform interface
- connector shells
- connector stiffening clips
- cover assembly, hammer bank / ribbon mask
- cover assembly, shuttle
- cover assembly, top, pedestal model
- doors, cabinet, reversing
- ethernet interface assemblies
- fan assembly, cabinet exhaust
- fan assembly, card cage
- fan assembly, hammer bank
- hammer spring assembly
- ibm coax/twinax expansion board
- magnetic pick-up (mpu) assembly
- memory and security modules
- motor assembly, paper feed
- motor assembly, platen open
- motor assembly, ribbon drive
- network print server
- operator panel assembly, cabinet model
- operator panel assembly, pedestal model
- paper guide assembly
- paper ironer
- resistors, terminating
- ribbon guide assembly (l/r)
- ribbon hub
- shaft, splined
- shaft, support
- spring, extension
- switch assembly, cover open
- switch assembly, paper detector
- switch assembly, platen interlock
- tractor (l/r)
- illustrations of printer components
- a wire data
- printer specifications
- paper specifications
- printer dimensions
- electrical characteristics
- duty cycle
- c metric conversion tables
- mass and density
- d torque table
- safety inspection guide
- prepare the printer for inspection
- print mechanism
- power cable
- g cords and adapters
- part numbers
- i noise suppression devices
- j surestak power stacker
- stacker operation
- stacker control panel
- removing the power stacker
- installing the power stacker
- replacing the constant force spring
- replacing the timing belts
- illustrated parts breakdown
|
Table of ContentsMass and Density..........................................................................338Temperature..................................................................................338Power ............................................................................................338D Torque Table..................................................... 339E Safety Inspection Guide .................................... 341Safety Inspections ...............................................................................341Preparation ..........................................................................................341Prepare The Printer for Inspection.......................................................342Inspect Mechanical Parts.....................................................................342Inspect Electrical Parts ........................................................................343F Abbreviations And Signal Mnemonics............... 347G Cords And Adapters ......................................... 355H Part Numbers.................................................... 357I Noise Suppression Devices................................ 365J SureStak Power Stacker.................................... 367Contents ..............................................................................................367Introduction ..........................................................................................368Stacker Operation................................................................................368Removing The Power Stacker .............................................................375Installing The Power Stacker ...............................................................380Replacing The Constant Force Spring.................................................391Replacing The Timing Belts.................................................................394Illustrated Parts Breakdown.................................................................398
|
