IKEA RENGORA Manual
Also see for RENGORA: Installation instructionsManualManualManualManual
                                    |
ENGLISH 11NATURALDRYDoor opening system NaturalDry is a convection drying systemwhich automatically opens the door during/after drying phaseto ensure exceptional drying performance every day. Dooropens at the temperature that is safe to your kitchen furniture.As additional steam protection, special designed protection foilis added together with the dishwasher. To see how to mountprotection foil please refer to (ASSEMBLY INSTRUCTION).NaturalDry functionality could be disabled by the user asfollows:1. Go to the Dishwasher software menu pressing and holding1. Press the DELAY button: the corresponding «h» symbolappears on the display; each time you press the button,the time (1h, 2h, etc. up to max. 12h) from the start ofthe selected wash cycle will be increased.2. Select the wash program, press the START/PAUSEbutton and within 4 seconds close the door: the timerwill begin counting down.3. Once this time has elapsed, the indicator light «h»switches off and the wash cycle begins.To adjust the delay time and select a shorter period of time,press the DELAY button. To cancel it, press the buttonrepeatedly until the selected delayed start indicator light«h» switches off.The DELAY function cannot be set once a wash cyclehas been started.NaturalDryDoor opening system NaturalDry is a convection drying systemwhich automatically opens the door during/after drying phase toensure exceptional drying performance every day. Door opens atthe temperature that is safe to your kitchen furniture.As additional steam protection, special designed protection foil isadded together with the dishwasher. To see how to mount protec-tion foil please refer to (INSTALLATION GUIDE).NaturalDry functionality could be disabled by the user as follows:1. Go to the Dishwasher software menu pressing and holdingbutton (6 sec).2. You switched to NaturalDry Control Menu, you could changestatus of NaturalDry functionality by pressing button:E – enabled d – disabledTo confirm the change and exit from the Control Menu pleasepress and hold button (3 sec).DELAYThe start time of the program may be delayed for a periodof time between 1 and 12 hours.ProgramDryingphaseNaturalDry Availableoptions *)Duration ofwash pro-gram(h:min)**)Waterconsumption(litres/cycle)Energyconsumption(kWh/cycle)50° 2:45 12.0 0.92EcoConventionalwash and dry 55° 2:00 15.0 1.35Intensive 65° - 2:30 15.0 1.50Fast 50° - - 0:55 11.5 1.10Sanitizing 65° - 1:40 11.5 1.30Pre-Wash - - - 0:10 4.5 0.01Self-Clean 65° - - 0:50 8.0 0.80ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the followingaddress: dw_test_support@whirlpool.comPre-treatment of the dishes is not needed before any of the programs.*) Not all options can be used simultaneously.**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on manyfactors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type ofload, load balancing, additional selected options and sensor calibration.Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 WPROGRAMS DESCRIPTIONbutton (6 sec).2. You switched to NaturalDry Control Menu, you could changestatus of NaturalDry functionality by pressing button1. Press the DELAY button: the corresponding «h» symbolappears on the display; each time you press the button,the time (1h, 2h, etc. up to max. 12h) from the start ofthe selected wash cycle will be increased.2. Select the wash program, press the START/PAUSEbutton and within 4 seconds close the door: the timerwill begin counting down.3. Once this time has elapsed, the indicator light «h»switches off and the wash cycle begins.To adjust the delay time and select a shorter period of time,press the DELAY button. To cancel it, press the buttonrepeatedly until the selected delayed start indicator light«h» switches off.The DELAY function cannot be set once a wash cyclehas been started.NaturalDryDoor opening system NaturalDry is a convection dryingwhich automatically opens the door during/after dryingensure exceptional drying performance every day. Doothe temperature that is safe to your kitchen furniture.As additional steam protection, special designed protecadded together with the dishwasher. To see how to motion foil please refer to (INSTALLATION GUIDE).NaturalDry functionality could be disabled by the user a1. Go to the Dishwasher software menu pressing and hbutton (6 sec).2. You switched to NaturalDry Control Menu, you couldstatus of NaturalDry functionality by pressing buttoE – enabled d – disabledTo confirm the change and exit from the Control Menupress and hold button (3 sec).DELAYThe start time of the program may be delayed for a periodof time between 1 and 12 hours.ProgramDryingphaseNaturalDry Availableoptions *)Duration ofwash pro-gram(h:min)**)Waterconsumption(litres/cycle)Encons(kW50° 2:45 12.0 01 Eco2 Conventionalwash and dry 55° 2:00 15.0 13 Intensive 65° - 2:30 15.0 14 Fast 50° - - 0:55 11.5 15 Sanitizing 65° - 1:40 11.5 16 Pre-Wash - - - 0:10 4.5 07 Self-Clean 65° - - 0:50 8.0 0ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the foaddress: dw_test_support@whirlpool.comPre-treatment of the dishes is not needed before any of the programs.*) Not all options can be used simultaneously.**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on mfactors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity andload, load balancing, additional selected options and sensor calibration.Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 WPROGRAMS DESCRIPTION:E – enabled d – disabledTo confirm the change and exit from the Control Menuplease press and hold9ENGLISH1. Press the DELAY button: the corresponding «h» symbolappears on the display; each time you press the button,the time (1h, 2h, etc. up to max. 12h) from the start ofthe selected wash cycle will be increased.2. Select the wash program, press the START/PAUSEbutton and within 4 seconds close the door: the timerwill begin counting down.3. Once this time has elapsed, the indicator light «h»switches off and the wash cycle begins.To adjust the delay time and select a shorter period of time,press the DELAY button. To cancel it, press the buttonrepeatedly until the selected delayed start indicator light«h» switches off.The DELAY function cannot be set once a wash cyclehas been started.NaturalDryDoor opening system NaturalDry is a convection drying systemwhich automatically opens the door during/after drying phase toensure exceptional drying performance every day. Door opens atthe temperature that is safe to your kitchen furniture.As additional steam protection, special designed protection foil isadded together with the dishwasher. To see how to mount protec-tion foil please refer to (INSTALLATION GUIDE).NaturalDry functionality could be disabled by the user as follows:1. Go to the Dishwasher software menu pressing and holdingbutton (6 sec).2. You switched to NaturalDry Control Menu, you could changestatus of NaturalDry functionality by pressing button:E – enabled d – disabledTo confirm the change and exit from the Control Menu pleasepress and hold button (3 sec).DELAYThe start time of the program may be delayed for a periodof time between 1 and 12 hours.ProgramDryingphaseNaturalDry Availableoptions *)Duration ofwash pro-gram(h:min)**)Waterconsumption(litres/cycle)Energyconsumption(kWh/cycle)50° 2:45 12.0 0.921 Eco2 Conventionalwash and dry 55° 2:00 15.0 1.353 Intensive 65° - 2:30 15.0 1.504 Fast 50° - - 0:55 11.5 1.105 Sanitizing 65° - 1:40 11.5 1.306 Pre-Wash - - - 0:10 4.5 0.017 Self-Clean 65° - - 0:50 8.0 0.80ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the followingaddress: dw_test_support@whirlpool.comPre-treatment of the dishes is not needed before any of the programs.*) Not all options can be used simultaneously.**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on manyfactors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type ofload, load balancing, additional selected options and sensor calibration.Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 WPROGRAMS DESCRIPTIONbutton (3 sec).ECO program data is measured under laboratory conditionsaccording to European Standard EN 60436:2020.Note for Test Laboratories: For information on comparativeEN testing conditions, please send an email to the followingaddress: dw_test_support@whirlpool.comPre-treatment of the dishes is not needed before any of theprograms.*) Not all options can be used simultaneously.**) Values given for programes other than the eco program areindicative only. The actual time may vary depending on manyfactors such as temperature and pressure of the incomingwater, room temperature, amount of detergent, quantity andtype of load, load balancing, additional selected options andsensor calibration.1. ECO - Eco program is suitable to clean normally soiledtableware, that for this use, it is the most efficient programin terms of its combined energy and water consumption, andthat it is used to assess compliance with the EU Ecodesignlegislation.2. CONVENTIONAL WASH AND DRY - Mixed soil. For normallysoiled dishes with dried food residues.3. INTENSIVE - Program recommended for heavily soiledcrockery, especially suitable for pans and saucepans (not tobe used for delicate items).4. FAST WASH - Program for limited quantity of normally soiledcrockery. Ensures optimal cleaning performance in shortertime.5. SANITIZING - Normally or heavily soiled crockery, withadditional antibacterial wash. Can be used to performmaintenance of the dishwasher.6. PRE-WASH - Use to refresh crockery planned to be washedlater. No detergent to be used with this program.7. SELF-CLEAN - Program to be used to perform maintenanceof the dishwasher, to be carried out only when thedishwasher is EMPTY using specific detergents designed fordishwasher maintenance.FUNCTIONS can be selected directly by pressing thecorresponding button (see CONTROL PANEL).If a function is not compatible with the selected programsee PROGRAMS TABLE, the corresponding LED rapidly 3times and beeps will sound. The option will not be enabled.ProgramDryingphaseNaturalDryAvailablefunctions *)Duration ofwash program(h:min)**)Waterconsumption(litres/cycle)Energyconsumption(kWh/cycle)1 Eco1. Press the DELAY button: the corresponding «h» symbolappears on the display; each time you press the button,the time (1h, 2h, etc. up to max. 12h) from the start ofthe selected wash cycle will be increased.2. Select the wash program, press the START/PAUSEbutton and within 4 seconds close the door: the timerwill begin counting down.3. Once this time has elapsed, the indicator light «h»switches off and the wash cycle begins.To adjust the delay time and select a shorter period of time,press the DELAY button. To cancel it, press the buttonrepeatedly until the selected delayed start indicator light«h» switches off.The DELAY function cannot be set once a wash cyclehas been started.NaturalDryDoor opening system NaturalDry is a convection drying systemwhich automatically opens the door during/after drying phase toensure exceptional drying performance every day. Door opens atthe temperature that is safe to your kitchen furniture.As additional steam protection, special designed protection foil isadded together with the dishwasher. To see how to mount protec-tion foil please refer to (INSTALLATION GUIDE).NaturalDry functionality could be disabled by the user as follows:1. Go to the Dishwasher software menu pressing and holdingbutton (6 sec).2. You switched to NaturalDry Control Menu, you could changestatus of NaturalDry functionality by pressing button:E – enabled d – disabledTo confirm the change and exit from the Control Menu pleasepress and hold button (3 sec).DELAYThe start time of the program may be delayed for a periodof time between 1 and 12 hours.ProgramDryingphaseNaturalDry Availableoptions *)Duration ofwash pro-gram(h:min)**)Waterconsumption(litres/cycle)Energyconsumption(kWh/cycle)50° 2:45 12.0 0.921 Eco2 Conventionalwash and dry 55° 2:00 15.0 1.353 Intensive 65° - 2:30 15.0 1.504 Fast 50° - - 0:55 11.5 1.105 Sanitizing 65° - 1:40 11.5 1.306 Pre-Wash - - - 0:10 4.5 0.017 Self-Clean 65° - - 0:50 8.0 0.80ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the followingaddress: dw_test_support@whirlpool.comPre-treatment of the dishes is not needed before any of the programs.*) Not all options can be used simultaneously.**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on manyfactors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type ofload, load balancing, additional selected options and sensor calibration.Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 WPROGRAMS DESCRIPTION50°9ENGLISH1. Press the DELAY button: the corresponding «h» symbolappears on the display; each time you press the button,the time (1h, 2h, etc. up to max. 12h) from the start ofthe selected wash cycle will be increased.2. Select the wash program, press the START/PAUSEbutton and within 4 seconds close the door: the timerwill begin counting down.3. Once this time has elapsed, the indicator light «h»switches off and the wash cycle begins.To adjust the delay time and select a shorter period of time,press the DELAY button. To cancel it, press the buttonrepeatedly until the selected delayed start indicator light«h» switches off.The DELAY function cannot be set once a wash cyclehas been started.NaturalDryDoor opening system NaturalDry is a convection drying systemwhich automatically opens the door during/after drying phase toensure exceptional drying performance every day. Door opens atthe temperature that is safe to your kitchen furniture.As additional steam protection, special designed protection foil isadded together with the dishwasher. To see how to mount protec-tion foil please refer to (INSTALLATION GUIDE).NaturalDry functionality could be disabled by the user as follows:1. Go to the Dishwasher software menu pressing and holdingbutton (6 sec).2. You switched to NaturalDry Control Menu, you could changestatus of NaturalDry functionality by pressing button:E – enabled d – disabledTo confirm the change and exit from the Control Menu pleasepress and hold button (3 sec).DELAYThe start time of the program may be delayed for a periodof time between 1 and 12 hours.ProgramDryingphaseNaturalDry Availableoptions *)Duration ofwash pro-gram(h:min)**)Waterconsumption(litres/cycle)Energyconsumption(kWh/cycle)50° 2:45 12.0 0.921 Eco2 Conventionalwash and dry 55° 2:00 15.0 1.353 Intensive 65° - 2:30 15.0 1.504 Fast 50° - - 0:55 11.5 1.105 Sanitizing 65° - 1:40 11.5 1.306 Pre-Wash - - - 0:10 4.5 0.017 Self-Clean 65° - - 0:50 8.0 0.80ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the followingaddress: dw_test_support@whirlpool.comPre-treatment of the dishes is not needed before any of the programs.*) Not all options can be used simultaneously.**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on manyfactors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type ofload, load balancing, additional selected options and sensor calibration.Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 WPROGRAMS DESCRIPTION9ENGLISH1. Press the DELAY button: the corresponding «h» symbolappears on the display; each time you press the button,the time (1h, 2h, etc. up to max. 12h) from the start ofthe selected wash cycle will be increased.2. Select the wash program, press the START/PAUSEbutton and within 4 seconds close the door: the timerwill begin counting down.3. Once this time has elapsed, the indicator light «h»switches off and the wash cycle begins.To adjust the delay time and select a shorter period of time,press the DELAY button. To cancel it, press the buttonrepeatedly until the selected delayed start indicator light«h» switches off.The DELAY function cannot be set once a wash cyclehas been started.NaturalDryDoor opening system NaturalDry is a convection drying systemwhich automatically opens the door during/after drying phase toensure exceptional drying performance every day. Door opens atthe temperature that is safe to your kitchen furniture.As additional steam protection, special designed protection foil isadded together with the dishwasher. To see how to mount protec-tion foil please refer to (INSTALLATION GUIDE).NaturalDry functionality could be disabled by the user as follows:1. Go to the Dishwasher software menu pressing and holdingbutton (6 sec).2. You switched to NaturalDry Control Menu, you could changestatus of NaturalDry functionality by pressing button:E – enabled d – disabledTo confirm the change and exit from the Control Menu pleasepress and hold button (3 sec).DELAYThe start time of the program may be delayed for a periodof time between 1 and 12 hours.ProgramDryingphaseNaturalDry Availableoptions *)Duration ofwash pro-gram(h:min)**)Waterconsumption(litres/cycle)Energyconsumption(kWh/cycle)50° 2:45 12.0 0.921 Eco2 Conventionalwash and dry 55° 2:00 15.0 1.353 Intensive 65° - 2:30 15.0 1.504 Fast 50° - - 0:55 11.5 1.105 Sanitizing 65° - 1:40 11.5 1.306 Pre-Wash - - - 0:10 4.5 0.017 Self-Clean 65° - - 0:50 8.0 0.80ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the followingaddress: dw_test_support@whirlpool.comPre-treatment of the dishes is not needed before any of the programs.*) Not all options can be used simultaneously.**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on manyfactors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type ofload, load balancing, additional selected options and sensor calibration.Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 WPROGRAMS DESCRIPTION9ENGLISH1. Press the DELAY button: the corresponding «h» symbolappears on the display; each time you press the button,the time (1h, 2h, etc. up to max. 12h) from the start ofthe selected wash cycle will be increased.2. Select the wash program, press the START/PAUSEbutton and within 4 seconds close the door: the timerwill begin counting down.3. Once this time has elapsed, the indicator light «h»switches off and the wash cycle begins.To adjust the delay time and select a shorter period of time,press the DELAY button. To cancel it, press the buttonrepeatedly until the selected delayed start indicator light«h» switches off.The DELAY function cannot be set once a wash cyclehas been started.NaturalDryDoor opening system NaturalDry is a convection drying systemwhich automatically opens the door during/after drying phase toensure exceptional drying performance every day. Door opens atthe temperature that is safe to your kitchen furniture.As additional steam protection, special designed protection foil isadded together with the dishwasher. To see how to mount protec-tion foil please refer to (INSTALLATION GUIDE).NaturalDry functionality could be disabled by the user as follows:1. Go to the Dishwasher software menu pressing and holdingbutton (6 sec).2. You switched to NaturalDry Control Menu, you could changestatus of NaturalDry functionality by pressing button:E – enabled d – disabledTo confirm the change and exit from the Control Menu pleasepress and hold button (3 sec).DELAYThe start time of the program may be delayed for a periodof time between 1 and 12 hours.ProgramDryingphaseNaturalDry Availableoptions *)Duration ofwash pro-gram(h:min)**)Waterconsumption(litres/cycle)Energyconsumption(kWh/cycle)50° 2:45 12.0 0.921 Eco2 Conventionalwash and dry 55° 2:00 15.0 1.353 Intensive 65° - 2:30 15.0 1.504 Fast 50° - - 0:55 11.5 1.105 Sanitizing 65° - 1:40 11.5 1.306 Pre-Wash - - - 0:10 4.5 0.017 Self-Clean 65° - - 0:50 8.0 0.80ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the followingaddress: dw_test_support@whirlpool.comPre-treatment of the dishes is not needed before any of the programs.*) Not all options can be used simultaneously.**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on manyfactors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type ofload, load balancing, additional selected options and sensor calibration.Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 WPROGRAMS DESCRIPTION2:45 12.0 0.942 Conventionalwash and dry9ENGLISH1. Press the DELAY button: the corresponding «h» symbolappears on the display; each time you press the button,the time (1h, 2h, etc. up to max. 12h) from the start ofthe selected wash cycle will be increased.2. Select the wash program, press the START/PAUSEbutton and within 4 seconds close the door: the timerwill begin counting down.3. Once this time has elapsed, the indicator light «h»switches off and the wash cycle begins.To adjust the delay time and select a shorter period of time,press the DELAY button. To cancel it, press the buttonrepeatedly until the selected delayed start indicator light«h» switches off.The DELAY function cannot be set once a wash cyclehas been started.NaturalDryDoor opening system NaturalDry is a convection drying systemwhich automatically opens the door during/after drying phase toensure exceptional drying performance every day. Door opens atthe temperature that is safe to your kitchen furniture.As additional steam protection, special designed protection foil isadded together with the dishwasher. To see how to mount protec-tion foil please refer to (INSTALLATION GUIDE).NaturalDry functionality could be disabled by the user as follows:1. Go to the Dishwasher software menu pressing and holdingbutton (6 sec).2. You switched to NaturalDry Control Menu, you could changestatus of NaturalDry functionality by pressing button:E – enabled d – disabledTo confirm the change and exit from the Control Menu pleasepress and hold button (3 sec).DELAYThe start time of the program may be delayed for a periodof time between 1 and 12 hours.ProgramDryingphaseNaturalDry Availableoptions *)Duration ofwash pro-gram(h:min)**)Waterconsumption(litres/cycle)Energyconsumption(kWh/cycle)50° 2:45 12.0 0.921 Eco2 Conventionalwash and dry 55° 2:00 15.0 1.353 Intensive 65° - 2:30 15.0 1.504 Fast 50° - - 0:55 11.5 1.105 Sanitizing 65° - 1:40 11.5 1.306 Pre-Wash - - - 0:10 4.5 0.017 Self-Clean 65° - - 0:50 8.0 0.80ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the followingaddress: dw_test_support@whirlpool.comPre-treatment of the dishes is not needed before any of the programs.*) Not all options can be used simultaneously.**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on manyfactors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type ofload, load balancing, additional selected options and sensor calibration.Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 WPROGRAMS DESCRIPTION55°9ENGLISH1. Press the DELAY button: the corresponding «h» symbolappears on the display; each time you press the button,the time (1h, 2h, etc. up to max. 12h) from the start ofthe selected wash cycle will be increased.2. Select the wash program, press the START/PAUSEbutton and within 4 seconds close the door: the timerwill begin counting down.3. Once this time has elapsed, the indicator light «h»switches off and the wash cycle begins.To adjust the delay time and select a shorter period of time,press the DELAY button. To cancel it, press the buttonrepeatedly until the selected delayed start indicator light«h» switches off.The DELAY function cannot be set once a wash cyclehas been started.NaturalDryDoor opening system NaturalDry is a convection drying systemwhich automatically opens the door during/after drying phase toensure exceptional drying performance every day. Door opens atthe temperature that is safe to your kitchen furniture.As additional steam protection, special designed protection foil isadded together with the dishwasher. To see how to mount protec-tion foil please refer to (INSTALLATION GUIDE).NaturalDry functionality could be disabled by the user as follows:1. Go to the Dishwasher software menu pressing and holdingbutton (6 sec).2. You switched to NaturalDry Control Menu, you could changestatus of NaturalDry functionality by pressing button:E – enabled d – disabledTo confirm the change and exit from the Control Menu pleasepress and hold button (3 sec).DELAYThe start time of the program may be delayed for a periodof time between 1 and 12 hours.ProgramDryingphaseNaturalDry Availableoptions *)Duration ofwash pro-gram(h:min)**)Waterconsumption(litres/cycle)Energyconsumption(kWh/cycle)50° 2:45 12.0 0.921 Eco2 Conventionalwash and dry 55° 2:00 15.0 1.353 Intensive 65° - 2:30 15.0 1.504 Fast 50° - - 0:55 11.5 1.105 Sanitizing 65° - 1:40 11.5 1.306 Pre-Wash - - - 0:10 4.5 0.017 Self-Clean 65° - - 0:50 8.0 0.80ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the followingaddress: dw_test_support@whirlpool.comPre-treatment of the dishes is not needed before any of the programs.*) Not all options can be used simultaneously.**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on manyfactors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type ofload, load balancing, additional selected options and sensor calibration.Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 WPROGRAMS DESCRIPTION9ENGLISH1. Press the DELAY button: the corresponding «h» symbolappears on the display; each time you press the button,the time (1h, 2h, etc. up to max. 12h) from the start ofthe selected wash cycle will be increased.2. Select the wash program, press the START/PAUSEbutton and within 4 seconds close the door: the timerwill begin counting down.3. Once this time has elapsed, the indicator light «h»switches off and the wash cycle begins.To adjust the delay time and select a shorter period of time,press the DELAY button. To cancel it, press the buttonrepeatedly until the selected delayed start indicator light«h» switches off.The DELAY function cannot be set once a wash cyclehas been started.NaturalDryDoor opening system NaturalDry is a convection drying systemwhich automatically opens the door during/after drying phase toensure exceptional drying performance every day. Door opens atthe temperature that is safe to your kitchen furniture.As additional steam protection, special designed protection foil isadded together with the dishwasher. To see how to mount protec-tion foil please refer to (INSTALLATION GUIDE).NaturalDry functionality could be disabled by the user as follows:1. Go to the Dishwasher software menu pressing and holdingbutton (6 sec).2. You switched to NaturalDry Control Menu, you could changestatus of NaturalDry functionality by pressing button:E – enabled d – disabledTo confirm the change and exit from the Control Menu pleasepress and hold button (3 sec).DELAYThe start time of the program may be delayed for a periodof time between 1 and 12 hours.ProgramDryingphaseNaturalDry Availableoptions *)Duration ofwash pro-gram(h:min)**)Waterconsumption(litres/cycle)Energyconsumption(kWh/cycle)50° 2:45 12.0 0.921 Eco2 Conventionalwash and dry 55° 2:00 15.0 1.353 Intensive 65° - 2:30 15.0 1.504 Fast 50° - - 0:55 11.5 1.105 Sanitizing 65° - 1:40 11.5 1.306 Pre-Wash - - - 0:10 4.5 0.017 Self-Clean 65° - - 0:50 8.0 0.80ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the followingaddress: dw_test_support@whirlpool.comPre-treatment of the dishes is not needed before any of the programs.*) Not all options can be used simultaneously.**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on manyfactors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type ofload, load balancing, additional selected options and sensor calibration.Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 WPROGRAMS DESCRIPTION9ENGLISH1. Press the DELAY button: the corresponding «h» symbolappears on the display; each time you press the button,the time (1h, 2h, etc. up to max. 12h) from the start ofthe selected wash cycle will be increased.2. Select the wash program, press the START/PAUSEbutton and within 4 seconds close the door: the timerwill begin counting down.3. Once this time has elapsed, the indicator light «h»switches off and the wash cycle begins.To adjust the delay time and select a shorter period of time,press the DELAY button. To cancel it, press the buttonrepeatedly until the selected delayed start indicator light«h» switches off.The DELAY function cannot be set once a wash cyclehas been started.NaturalDryDoor opening system NaturalDry is a convection drying systemwhich automatically opens the door during/after drying phase toensure exceptional drying performance every day. Door opens atthe temperature that is safe to your kitchen furniture.As additional steam protection, special designed protection foil isadded together with the dishwasher. To see how to mount protec-tion foil please refer to (INSTALLATION GUIDE).NaturalDry functionality could be disabled by the user as follows:1. Go to the Dishwasher software menu pressing and holdingbutton (6 sec).2. You switched to NaturalDry Control Menu, you could changestatus of NaturalDry functionality by pressing button:E – enabled d – disabledTo confirm the change and exit from the Control Menu pleasepress and hold button (3 sec).DELAYThe start time of the program may be delayed for a periodof time between 1 and 12 hours.ProgramDryingphaseNaturalDry Availableoptions *)Duration ofwash pro-gram(h:min)**)Waterconsumption(litres/cycle)Energyconsumption(kWh/cycle)50° 2:45 12.0 0.921 Eco2 Conventionalwash and dry 55° 2:00 15.0 1.353 Intensive 65° - 2:30 15.0 1.504 Fast 50° - - 0:55 11.5 1.105 Sanitizing 65° - 1:40 11.5 1.306 Pre-Wash - - - 0:10 4.5 0.017 Self-Clean 65° - - 0:50 8.0 0.80ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the followingaddress: dw_test_support@whirlpool.comPre-treatment of the dishes is not needed before any of the programs.*) Not all options can be used simultaneously.**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on manyfactors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type ofload, load balancing, additional selected options and sensor calibration.Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 WPROGRAMS DESCRIPTION2:00 15.0 1.353 Intensive9ENGLISH1. Press the DELAY button: the corresponding «h» symbolappears on the display; each time you press the button,the time (1h, 2h, etc. up to max. 12h) from the start ofthe selected wash cycle will be increased.2. Select the wash program, press the START/PAUSEbutton and within 4 seconds close the door: the timerwill begin counting down.3. Once this time has elapsed, the indicator light «h»switches off and the wash cycle begins.To adjust the delay time and select a shorter period of time,press the DELAY button. To cancel it, press the buttonrepeatedly until the selected delayed start indicator light«h» switches off.The DELAY function cannot be set once a wash cyclehas been started.NaturalDryDoor opening system NaturalDry is a convection drying systemwhich automatically opens the door during/after drying phase toensure exceptional drying performance every day. Door opens atthe temperature that is safe to your kitchen furniture.As additional steam protection, special designed protection foil isadded together with the dishwasher. To see how to mount protec-tion foil please refer to (INSTALLATION GUIDE).NaturalDry functionality could be disabled by the user as follows:1. Go to the Dishwasher software menu pressing and holdingbutton (6 sec).2. You switched to NaturalDry Control Menu, you could changestatus of NaturalDry functionality by pressing button:E – enabled d – disabledTo confirm the change and exit from the Control Menu pleasepress and hold button (3 sec).DELAYThe start time of the program may be delayed for a periodof time between 1 and 12 hours.ProgramDryingphaseNaturalDry Availableoptions *)Duration ofwash pro-gram(h:min)**)Waterconsumption(litres/cycle)Energyconsumption(kWh/cycle)50° 2:45 12.0 0.921 Eco2 Conventionalwash and dry 55° 2:00 15.0 1.353 Intensive 65° - 2:30 15.0 1.504 Fast 50° - - 0:55 11.5 1.105 Sanitizing 65° - 1:40 11.5 1.306 Pre-Wash - - - 0:10 4.5 0.017 Self-Clean 65° - - 0:50 8.0 0.80ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the followingaddress: dw_test_support@whirlpool.comPre-treatment of the dishes is not needed before any of the programs.*) Not all options can be used simultaneously.**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on manyfactors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type ofload, load balancing, additional selected options and sensor calibration.Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 WPROGRAMS DESCRIPTION65°9ENGLISH1. Press the DELAY button: the corresponding «h» symbolappears on the display; each time you press the button,the time (1h, 2h, etc. up to max. 12h) from the start ofthe selected wash cycle will be increased.2. Select the wash program, press the START/PAUSEbutton and within 4 seconds close the door: the timerwill begin counting down.3. Once this time has elapsed, the indicator light «h»switches off and the wash cycle begins.To adjust the delay time and select a shorter period of time,press the DELAY button. To cancel it, press the buttonrepeatedly until the selected delayed start indicator light«h» switches off.The DELAY function cannot be set once a wash cyclehas been started.NaturalDryDoor opening system NaturalDry is a convection drying systemwhich automatically opens the door during/after drying phase toensure exceptional drying performance every day. Door opens atthe temperature that is safe to your kitchen furniture.As additional steam protection, special designed protection foil isadded together with the dishwasher. To see how to mount protec-tion foil please refer to (INSTALLATION GUIDE).NaturalDry functionality could be disabled by the user as follows:1. Go to the Dishwasher software menu pressing and holdingbutton (6 sec).2. You switched to NaturalDry Control Menu, you could changestatus of NaturalDry functionality by pressing button:E – enabled d – disabledTo confirm the change and exit from the Control Menu pleasepress and hold button (3 sec).DELAYThe start time of the program may be delayed for a periodof time between 1 and 12 hours.ProgramDryingphaseNaturalDry Availableoptions *)Duration ofwash pro-gram(h:min)**)Waterconsumption(litres/cycle)Energyconsumption(kWh/cycle)50° 2:45 12.0 0.921 Eco2 Conventionalwash and dry 55° 2:00 15.0 1.353 Intensive 65° - 2:30 15.0 1.504 Fast 50° - - 0:55 11.5 1.105 Sanitizing 65° - 1:40 11.5 1.306 Pre-Wash - - - 0:10 4.5 0.017 Self-Clean 65° - - 0:50 8.0 0.80ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the followingaddress: dw_test_support@whirlpool.comPre-treatment of the dishes is not needed before any of the programs.*) Not all options can be used simultaneously.**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on manyfactors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type ofload, load balancing, additional selected options and sensor calibration.Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 WPROGRAMS DESCRIPTION9ENGLISH1. Press the DELAY button: the corresponding «h» symbolappears on the display; each time you press the button,the time (1h, 2h, etc. up to max. 12h) from the start ofthe selected wash cycle will be increased.2. Select the wash program, press the START/PAUSEbutton and within 4 seconds close the door: the timerwill begin counting down.3. Once this time has elapsed, the indicator light «h»switches off and the wash cycle begins.To adjust the delay time and select a shorter period of time,press the DELAY button. To cancel it, press the buttonrepeatedly until the selected delayed start indicator light«h» switches off.The DELAY function cannot be set once a wash cyclehas been started.NaturalDryDoor opening system NaturalDry is a convection drying systemwhich automatically opens the door during/after drying phase toensure exceptional drying performance every day. Door opens atthe temperature that is safe to your kitchen furniture.As additional steam protection, special designed protection foil isadded together with the dishwasher. To see how to mount protec-tion foil please refer to (INSTALLATION GUIDE).NaturalDry functionality could be disabled by the user as follows:1. Go to the Dishwasher software menu pressing and holdingbutton (6 sec).2. You switched to NaturalDry Control Menu, you could changestatus of NaturalDry functionality by pressing button:E – enabled d – disabledTo confirm the change and exit from the Control Menu pleasepress and hold button (3 sec).DELAYThe start time of the program may be delayed for a periodof time between 1 and 12 hours.ProgramDryingphaseNaturalDry Availableoptions *)Duration ofwash pro-gram(h:min)**)Waterconsumption(litres/cycle)Energyconsumption(kWh/cycle)50° 2:45 12.0 0.921 Eco2 Conventionalwash and dry 55° 2:00 15.0 1.353 Intensive 65° - 2:30 15.0 1.504 Fast 50° - - 0:55 11.5 1.105 Sanitizing 65° - 1:40 11.5 1.306 Pre-Wash - - - 0:10 4.5 0.017 Self-Clean 65° - - 0:50 8.0 0.80ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the followingaddress: dw_test_support@whirlpool.comPre-treatment of the dishes is not needed before any of the programs.*) Not all options can be used simultaneously.**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on manyfactors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type ofload, load balancing, additional selected options and sensor calibration.Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 WPROGRAMS DESCRIPTION9ENGLISH1. Press the DELAY button: the corresponding «h» symbolappears on the display; each time you press the button,the time (1h, 2h, etc. up to max. 12h) from the start ofthe selected wash cycle will be increased.2. Select the wash program, press the START/PAUSEbutton and within 4 seconds close the door: the timerwill begin counting down.3. Once this time has elapsed, the indicator light «h»switches off and the wash cycle begins.To adjust the delay time and select a shorter period of time,press the DELAY button. To cancel it, press the buttonrepeatedly until the selected delayed start indicator light«h» switches off.The DELAY function cannot be set once a wash cyclehas been started.NaturalDryDoor opening system NaturalDry is a convection drying systemwhich automatically opens the door during/after drying phase toensure exceptional drying performance every day. Door opens atthe temperature that is safe to your kitchen furniture.As additional steam protection, special designed protection foil isadded together with the dishwasher. To see how to mount protec-tion foil please refer to (INSTALLATION GUIDE).NaturalDry functionality could be disabled by the user as follows:1. Go to the Dishwasher software menu pressing and holdingbutton (6 sec).2. You switched to NaturalDry Control Menu, you could changestatus of NaturalDry functionality by pressing button:E – enabled d – disabledTo confirm the change and exit from the Control Menu pleasepress and hold button (3 sec).DELAYThe start time of the program may be delayed for a periodof time between 1 and 12 hours.ProgramDryingphaseNaturalDry Availableoptions *)Duration ofwash pro-gram(h:min)**)Waterconsumption(litres/cycle)Energyconsumption(kWh/cycle)50° 2:45 12.0 0.921 Eco2 Conventionalwash and dry 55° 2:00 15.0 1.353 Intensive 65° - 2:30 15.0 1.504 Fast 50° - - 0:55 11.5 1.105 Sanitizing 65° - 1:40 11.5 1.306 Pre-Wash - - - 0:10 4.5 0.017 Self-Clean 65° - - 0:50 8.0 0.80ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the followingaddress: dw_test_support@whirlpool.comPre-treatment of the dishes is not needed before any of the programs.*) Not all options can be used simultaneously.**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on manyfactors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type ofload, load balancing, additional selected options and sensor calibration.Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 WPROGRAMS DESCRIPTION2:30 15.0 1.504 Fast Wash9ENGLISH1. Press the DELAY button: the corresponding «h» symbolappears on the display; each time you press the button,the time (1h, 2h, etc. up to max. 12h) from the start ofthe selected wash cycle will be increased.2. Select the wash program, press the START/PAUSEbutton and within 4 seconds close the door: the timerwill begin counting down.3. Once this time has elapsed, the indicator light «h»switches off and the wash cycle begins.To adjust the delay time and select a shorter period of time,press the DELAY button. To cancel it, press the buttonrepeatedly until the selected delayed start indicator light«h» switches off.The DELAY function cannot be set once a wash cyclehas been started.NaturalDryDoor opening system NaturalDry is a convection drying systemwhich automatically opens the door during/after drying phase toensure exceptional drying performance every day. Door opens atthe temperature that is safe to your kitchen furniture.As additional steam protection, special designed protection foil isadded together with the dishwasher. To see how to mount protec-tion foil please refer to (INSTALLATION GUIDE).NaturalDry functionality could be disabled by the user as follows:1. Go to the Dishwasher software menu pressing and holdingbutton (6 sec).2. You switched to NaturalDry Control Menu, you could changestatus of NaturalDry functionality by pressing button:E – enabled d – disabledTo confirm the change and exit from the Control Menu pleasepress and hold button (3 sec).DELAYThe start time of the program may be delayed for a periodof time between 1 and 12 hours.ProgramDryingphaseNaturalDry Availableoptions *)Duration ofwash pro-gram(h:min)**)Waterconsumption(litres/cycle)Energyconsumption(kWh/cycle)50° 2:45 12.0 0.921 Eco2 Conventionalwash and dry 55° 2:00 15.0 1.353 Intensive 65° - 2:30 15.0 1.504 Fast 50° - - 0:55 11.5 1.105 Sanitizing 65° - 1:40 11.5 1.306 Pre-Wash - - - 0:10 4.5 0.017 Self-Clean 65° - - 0:50 8.0 0.80ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the followingaddress: dw_test_support@whirlpool.comPre-treatment of the dishes is not needed before any of the programs.*) Not all options can be used simultaneously.**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on manyfactors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type ofload, load balancing, additional selected options and sensor calibration.Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 WPROGRAMS DESCRIPTION50° - -9ENGLISH1. Press the DELAY button: the corresponding «h» symbolappears on the display; each time you press the button,the time (1h, 2h, etc. up to max. 12h) from the start ofthe selected wash cycle will be increased.2. Select the wash program, press the START/PAUSEbutton and within 4 seconds close the door: the timerwill begin counting down.3. Once this time has elapsed, the indicator light «h»switches off and the wash cycle begins.To adjust the delay time and select a shorter period of time,press the DELAY button. To cancel it, press the buttonrepeatedly until the selected delayed start indicator light«h» switches off.The DELAY function cannot be set once a wash cyclehas been started.NaturalDryDoor opening system NaturalDry is a convection drying systemwhich automatically opens the door during/after drying phase toensure exceptional drying performance every day. Door opens atthe temperature that is safe to your kitchen furniture.As additional steam protection, special designed protection foil isadded together with the dishwasher. To see how to mount protec-tion foil please refer to (INSTALLATION GUIDE).NaturalDry functionality could be disabled by the user as follows:1. Go to the Dishwasher software menu pressing and holdingbutton (6 sec).2. You switched to NaturalDry Control Menu, you could changestatus of NaturalDry functionality by pressing button:E – enabled d – disabledTo confirm the change and exit from the Control Menu pleasepress and hold button (3 sec).DELAYThe start time of the program may be delayed for a periodof time between 1 and 12 hours.ProgramDryingphaseNaturalDry Availableoptions *)Duration ofwash pro-gram(h:min)**)Waterconsumption(litres/cycle)Energyconsumption(kWh/cycle)50° 2:45 12.0 0.921 Eco2 Conventionalwash and dry 55° 2:00 15.0 1.353 Intensive 65° - 2:30 15.0 1.504 Fast 50° - - 0:55 11.5 1.105 Sanitizing 65° - 1:40 11.5 1.306 Pre-Wash - - - 0:10 4.5 0.017 Self-Clean 65° - - 0:50 8.0 0.80ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the followingaddress: dw_test_support@whirlpool.comPre-treatment of the dishes is not needed before any of the programs.*) Not all options can be used simultaneously.**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on manyfactors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type ofload, load balancing, additional selected options and sensor calibration.Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 WPROGRAMS DESCRIPTION0:55 11.5 1.105 Sanitizing9ENGLISH1. Press the DELAY button: the corresponding «h» symbolappears on the display; each time you press the button,the time (1h, 2h, etc. up to max. 12h) from the start ofthe selected wash cycle will be increased.2. Select the wash program, press the START/PAUSEbutton and within 4 seconds close the door: the timerwill begin counting down.3. Once this time has elapsed, the indicator light «h»switches off and the wash cycle begins.To adjust the delay time and select a shorter period of time,press the DELAY button. To cancel it, press the buttonrepeatedly until the selected delayed start indicator light«h» switches off.The DELAY function cannot be set once a wash cyclehas been started.NaturalDryDoor opening system NaturalDry is a convection drying systemwhich automatically opens the door during/after drying phase toensure exceptional drying performance every day. Door opens atthe temperature that is safe to your kitchen furniture.As additional steam protection, special designed protection foil isadded together with the dishwasher. To see how to mount protec-tion foil please refer to (INSTALLATION GUIDE).NaturalDry functionality could be disabled by the user as follows:1. Go to the Dishwasher software menu pressing and holdingbutton (6 sec).2. You switched to NaturalDry Control Menu, you could changestatus of NaturalDry functionality by pressing button:E – enabled d – disabledTo confirm the change and exit from the Control Menu pleasepress and hold button (3 sec).DELAYThe start time of the program may be delayed for a periodof time between 1 and 12 hours.ProgramDryingphaseNaturalDry Availableoptions *)Duration ofwash pro-gram(h:min)**)Waterconsumption(litres/cycle)Energyconsumption(kWh/cycle)50° 2:45 12.0 0.921 Eco2 Conventionalwash and dry 55° 2:00 15.0 1.353 Intensive 65° - 2:30 15.0 1.504 Fast 50° - - 0:55 11.5 1.105 Sanitizing 65° - 1:40 11.5 1.306 Pre-Wash - - - 0:10 4.5 0.017 Self-Clean 65° - - 0:50 8.0 0.80ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the followingaddress: dw_test_support@whirlpool.comPre-treatment of the dishes is not needed before any of the programs.*) Not all options can be used simultaneously.**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on manyfactors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type ofload, load balancing, additional selected options and sensor calibration.Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 WPROGRAMS DESCRIPTION65°9ENGLISH1. Press the DELAY button: the corresponding «h» symbolappears on the display; each time you press the button,the time (1h, 2h, etc. up to max. 12h) from the start ofthe selected wash cycle will be increased.2. Select the wash program, press the START/PAUSEbutton and within 4 seconds close the door: the timerwill begin counting down.3. Once this time has elapsed, the indicator light «h»switches off and the wash cycle begins.To adjust the delay time and select a shorter period of time,press the DELAY button. To cancel it, press the buttonrepeatedly until the selected delayed start indicator light«h» switches off.The DELAY function cannot be set once a wash cyclehas been started.NaturalDryDoor opening system NaturalDry is a convection drying systemwhich automatically opens the door during/after drying phase toensure exceptional drying performance every day. Door opens atthe temperature that is safe to your kitchen furniture.As additional steam protection, special designed protection foil isadded together with the dishwasher. To see how to mount protec-tion foil please refer to (INSTALLATION GUIDE).NaturalDry functionality could be disabled by the user as follows:1. Go to the Dishwasher software menu pressing and holdingbutton (6 sec).2. You switched to NaturalDry Control Menu, you could changestatus of NaturalDry functionality by pressing button:E – enabled d – disabledTo confirm the change and exit from the Control Menu pleasepress and hold button (3 sec).DELAYThe start time of the program may be delayed for a periodof time between 1 and 12 hours.ProgramDryingphaseNaturalDry Availableoptions *)Duration ofwash pro-gram(h:min)**)Waterconsumption(litres/cycle)Energyconsumption(kWh/cycle)50° 2:45 12.0 0.921 Eco2 Conventionalwash and dry 55° 2:00 15.0 1.353 Intensive 65° - 2:30 15.0 1.504 Fast 50° - - 0:55 11.5 1.105 Sanitizing 65° - 1:40 11.5 1.306 Pre-Wash - - - 0:10 4.5 0.017 Self-Clean 65° - - 0:50 8.0 0.80ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the followingaddress: dw_test_support@whirlpool.comPre-treatment of the dishes is not needed before any of the programs.*) Not all options can be used simultaneously.**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on manyfactors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type ofload, load balancing, additional selected options and sensor calibration.Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 WPROGRAMS DESCRIPTION-9ENGLISH1. Press the DELAY button: the corresponding «h» symbolappears on the display; each time you press the button,the time (1h, 2h, etc. up to max. 12h) from the start ofthe selected wash cycle will be increased.2. Select the wash program, press the START/PAUSEbutton and within 4 seconds close the door: the timerwill begin counting down.3. Once this time has elapsed, the indicator light «h»switches off and the wash cycle begins.To adjust the delay time and select a shorter period of time,press the DELAY button. To cancel it, press the buttonrepeatedly until the selected delayed start indicator light«h» switches off.The DELAY function cannot be set once a wash cyclehas been started.NaturalDryDoor opening system NaturalDry is a convection drying systemwhich automatically opens the door during/after drying phase toensure exceptional drying performance every day. Door opens atthe temperature that is safe to your kitchen furniture.As additional steam protection, special designed protection foil isadded together with the dishwasher. To see how to mount protec-tion foil please refer to (INSTALLATION GUIDE).NaturalDry functionality could be disabled by the user as follows:1. Go to the Dishwasher software menu pressing and holdingbutton (6 sec).2. You switched to NaturalDry Control Menu, you could changestatus of NaturalDry functionality by pressing button:E – enabled d – disabledTo confirm the change and exit from the Control Menu pleasepress and hold button (3 sec).DELAYThe start time of the program may be delayed for a periodof time between 1 and 12 hours.ProgramDryingphaseNaturalDry Availableoptions *)Duration ofwash pro-gram(h:min)**)Waterconsumption(litres/cycle)Energyconsumption(kWh/cycle)50° 2:45 12.0 0.921 Eco2 Conventionalwash and dry 55° 2:00 15.0 1.353 Intensive 65° - 2:30 15.0 1.504 Fast 50° - - 0:55 11.5 1.105 Sanitizing 65° - 1:40 11.5 1.306 Pre-Wash - - - 0:10 4.5 0.017 Self-Clean 65° - - 0:50 8.0 0.80ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the followingaddress: dw_test_support@whirlpool.comPre-treatment of the dishes is not needed before any of the programs.*) Not all options can be used simultaneously.**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on manyfactors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type ofload, load balancing, additional selected options and sensor calibration.Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 WPROGRAMS DESCRIPTION1:40 11.5 1.306 Pre-Wash9ENGLISH1. Press the DELAY button: the corresponding «h» symbolappears on the display; each time you press the button,the time (1h, 2h, etc. up to max. 12h) from the start ofthe selected wash cycle will be increased.2. Select the wash program, press the START/PAUSEbutton and within 4 seconds close the door: the timerwill begin counting down.3. Once this time has elapsed, the indicator light «h»switches off and the wash cycle begins.To adjust the delay time and select a shorter period of time,press the DELAY button. To cancel it, press the buttonrepeatedly until the selected delayed start indicator light«h» switches off.The DELAY function cannot be set once a wash cyclehas been started.NaturalDryDoor opening system NaturalDry is a convection drying systemwhich automatically opens the door during/after drying phase toensure exceptional drying performance every day. Door opens atthe temperature that is safe to your kitchen furniture.As additional steam protection, special designed protection foil isadded together with the dishwasher. To see how to mount protec-tion foil please refer to (INSTALLATION GUIDE).NaturalDry functionality could be disabled by the user as follows:1. Go to the Dishwasher software menu pressing and holdingbutton (6 sec).2. You switched to NaturalDry Control Menu, you could changestatus of NaturalDry functionality by pressing button:E – enabled d – disabledTo confirm the change and exit from the Control Menu pleasepress and hold button (3 sec).DELAYThe start time of the program may be delayed for a periodof time between 1 and 12 hours.ProgramDryingphaseNaturalDry Availableoptions *)Duration ofwash pro-gram(h:min)**)Waterconsumption(litres/cycle)Energyconsumption(kWh/cycle)50° 2:45 12.0 0.921 Eco2 Conventionalwash and dry 55° 2:00 15.0 1.353 Intensive 65° - 2:30 15.0 1.504 Fast 50° - - 0:55 11.5 1.105 Sanitizing 65° - 1:40 11.5 1.306 Pre-Wash - - - 0:10 4.5 0.017 Self-Clean 65° - - 0:50 8.0 0.80ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the followingaddress: dw_test_support@whirlpool.comPre-treatment of the dishes is not needed before any of the programs.*) Not all options can be used simultaneously.**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on manyfactors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type ofload, load balancing, additional selected options and sensor calibration.Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 WPROGRAMS DESCRIPTION- - -9ENGLISH1. Press the DELAY button: the corresponding «h» symbolappears on the display; each time you press the button,the time (1h, 2h, etc. up to max. 12h) from the start ofthe selected wash cycle will be increased.2. Select the wash program, press the START/PAUSEbutton and within 4 seconds close the door: the timerwill begin counting down.3. Once this time has elapsed, the indicator light «h»switches off and the wash cycle begins.To adjust the delay time and select a shorter period of time,press the DELAY button. To cancel it, press the buttonrepeatedly until the selected delayed start indicator light«h» switches off.The DELAY function cannot be set once a wash cyclehas been started.NaturalDryDoor opening system NaturalDry is a convection drying systemwhich automatically opens the door during/after drying phase toensure exceptional drying performance every day. Door opens atthe temperature that is safe to your kitchen furniture.As additional steam protection, special designed protection foil isadded together with the dishwasher. To see how to mount protec-tion foil please refer to (INSTALLATION GUIDE).NaturalDry functionality could be disabled by the user as follows:1. Go to the Dishwasher software menu pressing and holdingbutton (6 sec).2. You switched to NaturalDry Control Menu, you could changestatus of NaturalDry functionality by pressing button:E – enabled d – disabledTo confirm the change and exit from the Control Menu pleasepress and hold button (3 sec).DELAYThe start time of the program may be delayed for a periodof time between 1 and 12 hours.ProgramDryingphaseNaturalDry Availableoptions *)Duration ofwash pro-gram(h:min)**)Waterconsumption(litres/cycle)Energyconsumption(kWh/cycle)50° 2:45 12.0 0.921 Eco2 Conventionalwash and dry 55° 2:00 15.0 1.353 Intensive 65° - 2:30 15.0 1.504 Fast 50° - - 0:55 11.5 1.105 Sanitizing 65° - 1:40 11.5 1.306 Pre-Wash - - - 0:10 4.5 0.017 Self-Clean 65° - - 0:50 8.0 0.80ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the followingaddress: dw_test_support@whirlpool.comPre-treatment of the dishes is not needed before any of the programs.*) Not all options can be used simultaneously.**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on manyfactors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type ofload, load balancing, additional selected options and sensor calibration.Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 WPROGRAMS DESCRIPTION0:10 4.5 0.017 Self-Clean9ENGLISH1. Press the DELAY button: the corresponding «h» symbolappears on the display; each time you press the button,the time (1h, 2h, etc. up to max. 12h) from the start ofthe selected wash cycle will be increased.2. Select the wash program, press the START/PAUSEbutton and within 4 seconds close the door: the timerwill begin counting down.3. Once this time has elapsed, the indicator light «h»switches off and the wash cycle begins.To adjust the delay time and select a shorter period of time,press the DELAY button. To cancel it, press the buttonrepeatedly until the selected delayed start indicator light«h» switches off.The DELAY function cannot be set once a wash cyclehas been started.NaturalDryDoor opening system NaturalDry is a convection drying systemwhich automatically opens the door during/after drying phase toensure exceptional drying performance every day. Door opens atthe temperature that is safe to your kitchen furniture.As additional steam protection, special designed protection foil isadded together with the dishwasher. To see how to mount protec-tion foil please refer to (INSTALLATION GUIDE).NaturalDry functionality could be disabled by the user as follows:1. Go to the Dishwasher software menu pressing and holdingbutton (6 sec).2. You switched to NaturalDry Control Menu, you could changestatus of NaturalDry functionality by pressing button:E – enabled d – disabledTo confirm the change and exit from the Control Menu pleasepress and hold button (3 sec).DELAYThe start time of the program may be delayed for a periodof time between 1 and 12 hours.ProgramDryingphaseNaturalDry Availableoptions *)Duration ofwash pro-gram(h:min)**)Waterconsumption(litres/cycle)Energyconsumption(kWh/cycle)50° 2:45 12.0 0.921 Eco2 Conventionalwash and dry 55° 2:00 15.0 1.353 Intensive 65° - 2:30 15.0 1.504 Fast 50° - - 0:55 11.5 1.105 Sanitizing 65° - 1:40 11.5 1.306 Pre-Wash - - - 0:10 4.5 0.017 Self-Clean 65° - - 0:50 8.0 0.80ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the followingaddress: dw_test_support@whirlpool.comPre-treatment of the dishes is not needed before any of the programs.*) Not all options can be used simultaneously.**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on manyfactors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type ofload, load balancing, additional selected options and sensor calibration.Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 WPROGRAMS DESCRIPTION65° - -9ENGLISH1. Press the DELAY button: the corresponding «h» symbolappears on the display; each time you press the button,the time (1h, 2h, etc. up to max. 12h) from the start ofthe selected wash cycle will be increased.2. Select the wash program, press the START/PAUSEbutton and within 4 seconds close the door: the timerwill begin counting down.3. Once this time has elapsed, the indicator light «h»switches off and the wash cycle begins.To adjust the delay time and select a shorter period of time,press the DELAY button. To cancel it, press the buttonrepeatedly until the selected delayed start indicator light«h» switches off.The DELAY function cannot be set once a wash cyclehas been started.NaturalDryDoor opening system NaturalDry is a convection drying systemwhich automatically opens the door during/after drying phase toensure exceptional drying performance every day. Door opens atthe temperature that is safe to your kitchen furniture.As additional steam protection, special designed protection foil isadded together with the dishwasher. To see how to mount protec-tion foil please refer to (INSTALLATION GUIDE).NaturalDry functionality could be disabled by the user as follows:1. Go to the Dishwasher software menu pressing and holdingbutton (6 sec).2. You switched to NaturalDry Control Menu, you could changestatus of NaturalDry functionality by pressing button:E – enabled d – disabledTo confirm the change and exit from the Control Menu pleasepress and hold button (3 sec).DELAYThe start time of the program may be delayed for a periodof time between 1 and 12 hours.ProgramDryingphaseNaturalDry Availableoptions *)Duration ofwash pro-gram(h:min)**)Waterconsumption(litres/cycle)Energyconsumption(kWh/cycle)50° 2:45 12.0 0.921 Eco2 Conventionalwash and dry 55° 2:00 15.0 1.353 Intensive 65° - 2:30 15.0 1.504 Fast 50° - - 0:55 11.5 1.105 Sanitizing 65° - 1:40 11.5 1.306 Pre-Wash - - - 0:10 4.5 0.017 Self-Clean 65° - - 0:50 8.0 0.80ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the followingaddress: dw_test_support@whirlpool.comPre-treatment of the dishes is not needed before any of the programs.*) Not all options can be used simultaneously.**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on manyfactors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type ofload, load balancing, additional selected options and sensor calibration.Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 WPROGRAMS DESCRIPTION0:50 8.0 0.80DOOR OPENINGEco 50° after 150 minConventional wash and dry 55° end of cycleIntensive 65° end of cycleFast wash 50° N/ASanitizing 65° N/APre-wash N/ASelf-Clean 65° N/A |
Related manuals for IKEA RENGORA
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine