Jenn-Air JGD3430WS Instructions Manual

Also see for 30" (76.2 cm) Cooktop: Installation instructions Installation instructions Installation instructions Installation instructions Instructions

Contents

3INSTALLATION REQUIREMENTSTools and PartsGather the required tools and parts before starting installation.Read and follow the instructions provided with any tools listedhere.Tools neededParts suppliedParts needed■ Metal ducting■ Vent clamps■ Jenn-Air wall capJenn-Air ® 6" (15.2 cm) Round Surface Wall Cap DamperOrder Part Number A406Jenn-Air ® 3¼" x 10" (8.3 x 25.4 cm) Surface Wall Cap DamperOrder Part Number A403To order, see the “Assistance or Service” section of the Useand Care Guide.Check local codes and consult gas supplier. Check existing gassupply and electrical supply. See “Electrical Requirements” and“Gas Supply Requirements” sections.It is recommended that all electrical connections be made by alicensed, qualified electrical installer.Location RequirementsIMPORTANT: Observe all governing codes and ordinances.When installing cooktop, use minimum dimensions given.■ It is the installer’s responsibility to comply with installationclearances specified on the model/serial rating plate. Themodel/serial rating plate is located on side of the downdraftplenum.■ To eliminate the risk of burns or fire by reaching over theheated surface units, cabinet storage space located abovethe surface units should be avoided. If cabinet storage is tobe provided, the risk can be reduced by installing a rangehood that projects horizontally a minimum of 5" (12.7 cm)beyond the bottom of the cabinets.■ The cooktop should be installed in a location away fromstrong draft areas, such as windows, doors and strongheating vents or fans.■ All openings in the wall or floor where cooktop is to beinstalled must be sealed.■ Cabinet opening dimensions that are shown must be used.Given dimensions are minimum clearances.■ Grounded electrical supply is required. See “ElectricalRequirements” section. Proper gas supply connection mustbe available. See “Gas Supply Requirements” section.■ The cooktop is designed to hang from the countertop by itsside or rear flanges.■ The gas and electric supply should be located as shown in“Cabinet Dimensions” section so that they are accessiblewithout requiring removal of the cooktop.■ Provide cutout in right rear corner of cutout enclosure asshown to provide clearance for gas inlet, power supply cord,and to allow the rating label to be visible.■ If cabinet has drawers, drawers will need to be removed anddrawer fronts installed on front of cabinet.IMPORTANT: An undercounter built-in oven cannot be installedunder this product.IMPORTANT: To avoid damage to your cabinets, check with yourbuilder or cabinet supplier to make sure that the materials usedwill not discolor, delaminate or sustain other damage.Mobile Home - Additional Installation RequirementsThe installation of this cooktop must conform to theManufactured Home Construction and Safety Standard, Title 24CFR, Part 3280 (formerly the Federal Standard for Mobile HomeConstruction and Safety, Title 24, HUD Part 280). When suchstandard is not applicable, use the Standard for ManufacturedHome Installations, ANSI A225.1/NFPA 501A or local codes.■ In Canada, the installation of this cooktop must conform withthe current standards CAN/CSA-A240-latest edition, or withlocal codes.Product Dimensions30" (76.2 cm) Cooktop■ Tape measure■ Flat-blade screwdriver■ Phillips head screwdriver■ Drill■ Level■ 6" (15.2 cm) socketextension■ Marker or pencil■ Pliers■ ¼" drill bit■ Jigsaw■ Ratchet with ³⁄₈" socket■ Pipe-joint compoundresistant to LP gas■ Noncorrosive leak-detectionsolution■ Vent grill■ Pre-filter■ LP conversion kit■ Burner caps■ Burner grates■ Pressure regulatorA. 21½" (54.6 cm)B. 19¹¹⁄₁₆" (50.0 cm)C. Model/serial rating plate locationCAB