Jenn-Air W10379136B Installation Manual

Also see for JS42NXFXDW: Design and planning guide Installation instructions Installation guide Installation guide Installation instructions

Contents

Jenn-Air W10379136B Installation Manual Manual pdf 18 page image

18■ After the refrigerator is leveled and aligned, remove theinstallation block from the door hinge and use it to check thespacing between the panels and adjacent cabinets.NOTE: The installation block is designed to provide accuratespacing for ³⁄₄" (1.9 cm), ³⁄₈" (9.53 mm) and ¹⁄₈" (3.18 mm).1. Place top of cardboard carton or plywood under refrigerator.Remove dolly.2. Move the refrigerator straight back and evenly into theopening. Be sure that the water tubing is not kinked and thepower supply cord is on top of the refrigerator.NOTE: If the power supply cord is behind the refrigerator, itwill not install properly.3. Make sure the installation block is flush with the adjacentcabinets.NOTE: To achieve a flush installation, it is critical to verify a³⁄₄" (1.9 cm) depth from the front face of the adjacentcabinetry to the refrigerator.Level and Align RefrigeratorIMPORTANT: All four leveling legs must contact the floor tosupport and stabilize the full weight of refrigerator. Rollers are formoving the refrigerator, not for permanent support.After moving the refrigerator to its final location:1. Use a ⁵⁄₁₆" socket driver to turn the leveling bolts clockwise toextend the legs to the floor as shown. The rollers should beoff the floor.2. Adjust the leveling legs to level and align the refrigerator fromleft to right and front to back so that the refrigerator is leveland aligned with the cabinets.3. Continue adjusting all of the leveling legs to raise therefrigerator until the top is within at least ¹⁄₄" (6.35 mm) of thetop soffit as shown.NOTE: If an anti-tip board has been used, adjust the levelinglegs until the top of the refrigerator is making contact with thebottom of the anti-tip board(s). Do not crush the compressorcover.IMPORTANT: Adjust in small increments to keep fromdamaging the cabinet trim and causing problems with thedoor alignment or top grille fit. To avoid damage to thecabinet or leveling legs, do not apply more than 50 inch-pounds (5.65 Nm) of torque to the leveling bolts. The levelinglegs can be extended to a maximum of 1¹⁄₄" (3.18 cm) belowthe rollers.4. After leveling the refrigerator, again use a straight edge or 4-ftlevel across the front of the refrigerator installation blocks tothe cabinets to check that the refrigerator is still flush.A. Adjacent cabinet or wallB. Installation blockC. Face of refrigerator¹⁄₈"(3.18 mm)³⁄₈"(9.53 mm)³⁄₄"(1.9 cm)BCA³⁄₄" (1.9 cm)WARNINGTip Over HazardRefrigerator is top heavy and tips easily when notcompletely installed.Keep doors taped closed until refrigerator iscompletely installed.Use two or more people to move and installrefrigerator.Failure to do so can result in death or serious injury.A. Rear leveling boltB. Front leveling boltA. Center board¹⁄₄" (6.35 mm) max. above refrigeratorB. Two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) boardsC. Attach to studs with six #8 x 3" (7.6 cm) screwsD. Compressor coverE. Distance from bottom of anti-tip board to floorA BABBAC2" (5 cm)D¹⁄₄" (6 mm)max.84"(213.4 cm)E