Kenwood KRF-V4550D Instruction Manual

Also see for KRF-V4550D: Service manual

16PreparationsPreparing for surround soundSpeaker settingsIf you selected other than "LRG" as the center speaker setting.1 SURR YES: Surround speakers are connected to the re-ceiver.2 SURR NO: No surround speakers are connected to thereceiver.9 Press the SET UP key to accept the setting.• The receiver enters the speaker volume level adjustment mode.• In steps 3 and 4, indications appear only for the selectedchannels of the speakers that require adjusting.Turn on the power to this receiver by pressing POWER andON/STANDBY key.Select a speaker system.1231 Press the SET UP key to make the subwoofer setting indica-tion (SUBW) appear.2 Use the MULTI CONTROL to select the appropriate subwoofersetting.1 SUBW YES: A subwoofer is connected to the receiver.2 SUBW NO: No subwoofer is connected to the receiver.• The initial setting is "SUBW YES".• When the setting "SUBW NO" is selected, the front speakersautomatically are set to "FRNT LRG" and the procedure skips tostep 5.• When subwoofer output sound is required select "FRNT NML".3 Press the SET UP key to accept the setting.• The front speakers setting indication (FRNT) appears.4 Use the MULTI CONTROL to select the appropriate frontspeakers setting.1 FRNT NML (normal): Average size front speakers areconnected to the receiver.2 FRNT LRG (large): Large front speakers areconnected to the receiver.5 Press the SET UP key to accept the setting.• The center speaker setting indication (CNTR) appears.Adjust the volume levels for the speakers.Sit in your normal listening position and listen to the test tone. Adjustthe volume levels for the speakers until all speakers seem to beequally loud.1 Use the MULTI CONTROL to adjust the volume when the testtone is being output from the speaker channel to be adjusted.The test tone issues from the speakers for 2 seconds at a timein the following sequence:Lch = Cch = Rch = RS = LS = SW = Lch• If you change the volume level settings for the speakers whilelistening to music, the settings referred to on this page are alsochanged. ¶• If the speaker setting selects are changed, the speaker levelsettings are reset.2 Press the SET UP key.• The receiver enters the mode for inputting the distance to thespeakers.To enable you to obtain optimum enjoyment from the receiver’slistening modes, make sure to complete the speaker settings(subwoofer, front, center, and surround speakers) as described below.Continued to next pageIf you selected "NML" as the front speakers setting.1 CNTR YES: A center speaker is connected to thereceiver.2 CNTR NO: No center speaker is connected to thereceiver.7 Press the SET UP key to accept the setting.• The surround speaker setting indication (SURR) appears.8 Use the MULTI CONTROL to select the appropriate surroundspeaker setting.If you selected "LRG" as the center speaker setting.1 SURR LRG (large): Large surround speakers are con-nected to the receiver.2 SURR NML (normal): Average size surround speakers areconnected to the receiver.3 SURR NO: No surround speakers are connectedto the receiver.FMAMMHzkHzPRO LOGIC3DOWN MIXDIGITALS.DIRECTMONITORDSPMEMOST.TUNEDAUTO SOUND AUTOLFECS RSLSTI.VOLBCLIP MUTERDS EON PTYTP TA NEWSSWRLSPSTEREOSTEREOR FMAMMHzkHzPRO LOGIC3DOWN MIXDIGITALS.DIRECTMONITORDSPMEMOST.TUNEDAUTO SOUND AUTOLFECS RSLSTI.VOLBCLIP MUTERDS EON PTYTP TA NEWSSWLSPFMAMMHzkHzPRO LOGIC3DOWN MIXDIGITALS.DIRECTMONITORDSPMEMOST.TUNEDAUTO SOUND AUTOLFECS RSLSTI.VOLBCLIP MUTERDS EON PTYTP TA NEWSSWRLSPSTEREO6 Use the MULTI CONTROL to select the appropriate centerspeaker setting.If you selected "LRG" as the front speakers setting.1 CNTR LRG (large): A large center speaker is connectedto the receiver.2 CNTR NML (normal): An average size center speaker isconnected to the receiver.3 CNTR NO: No center speaker is connected tothe receiver.The channel indication blinks while the test tone is being output.